Safety; Installation - PLYMOVENT ES-90/005 Instrucciones Para El Uso

below 30 A, e.g. gas or TIG welding, the cable sensor clamps
should be replaced by a light sensor, LS-12.
3

SaFEty

general
The manufacturer does not accept any liability for damage to
the product or personal injury caused by ignoring the safety
instructions in this manual, or by negligence during
installation, use, maintenance, and repair of the product
mentioned on the cover of this document and any
corresponding accessories. Specific working conditions or used
accessories may require additional safety instructions.
Immediately contact your supplier if you detect a potential
danger when using the product.
The user of the product is always fully responsible for
observing the local safety instructions and regulations.
user manual
- Everyone working on or with the product must be familiar
with the contents of this manual and must strictly observe
the instructions therein. The management should instruct the
personnel in accordance with the manual and observe all
instructions and directions given.
- Never change the order of the steps to perform.
- Always keep the manual with the product.
Pictograms and instructions on the product (if
present)
- The pictograms, warning and instructions attached to the
product are part of the safety features. They must not be
covered or removed and must be present and legible during
the entire life of the product.
- Immediately replace or repair damaged or illegible
pictograms, warnings and instructions.
users
The use of this product is exclusively reserved to authorised,
trained and qualified users. Temporary personnel and
personnel in training can only use the product under
supervision and responsibility of skilled engineers.
0000101011/190712/0 ES-90/005
The light sensor is
mounted on the extractor
near the hood. The light
sensor is either connected
to the energy saver
ES-90/005 which starts
and stops the fan, or is
connected to an
automatic damper ICE-LC
in a central system.
The light sensor LS-12
,
wall-mounted. The
maximum distance to the
work piece is about 3 m
(10 ft). Here it is
connected to an
automatic damper
ICE-LC, which opens and
closes the central fan. It
can also be connected to
the ES-90/005.
intended use
1
The product has been designed as a control box to operate an
extraction fan. Using the product for other purposes is
considered contrary to its intended use. The manufacturer
accepts no liability for any damages or injury resulting from
such use. The product has been built in accordance with
state-of-the-art standards and recognized safety regulations.
Only use this product when in technical perfect condition in
accordance with its intended use and the instructions
explained in the user manual.
Technical specifications
The specifications given in this manual must not be altered.
Modifications
Modification of (parts of) the product is not allowed, except
the bottom plate, which is allowed to be used as entrance
point for external cabling.

installation

- The installation of this product is exclusively reserved to
authorised, well-trained and qualified engineers.
- Inspect the product and check it for damage.
Verify the functioning of the safety features.
- Never install the product in front of entrances and exits
which must be used for emergency services.
- Make sure that the workshop, in the vicinity of the product,
contains sufficient approved fire extinguishers.
use
- Check the working environment. Do not allow unauthorised
persons to enter the working environment.
- Protect the product against water and humidity.
- Use common sense. Stay alert and keep your attention to
your work. Do not use the product when you are under the
influence of drugs, alcohol or medicine.
- Make sure the room is always sufficiently ventilated;
this applies especially to confined spaces.
Service, maintenance and repairs
waRNiNg!
Maintenance should only be performed by
authorised, qualified and trained persons (skilled)
using appropriate work practices.
waRNiNg!
Electrocution hazard
Disconnect mains before servicing. Failure to do so
could result in serious personal injury or death.
4 iNStaLLatiON
waRNiNg!
Do not attempt installation of this unit unless you
are familiar with the necessary tools, equipment,
utility connections and potential hazards.
Installation should be performed only by a qualified
service provider. Failure to do so could result in
reduced performance of the unit, serious personal
injury or death.
waRNiNg!
Fire hazard
Never install the control box in areas with
flammable gases.
1. "Intended use" as explained in EN-ISO 12100 is the use for which the technical
product is suited as specified by the manufacturer, inclusive of his directions in
the sales brochure. In case of doubt it is the use which can be deduced from
the construction, the model and the function of the technical product which is
considered normal use. Operating the machine within the limits of its intended
use also involves observing the instructions in the user manual.
EN - 4