JB Systems Light SIRIUS 60W LED Manual De Instrucciones página 6

ENGLISH
Please also check the chapter about the DMX-channel configuration of the unit to find out how you can force
a reset by DMX.
Home Position Adjust
Used to adjust the home position of several functions:
Make sure that the unit is connected to a DMX-controller and set to 11CH channel mode: set ch6 + ch7 to
maximum.
If you're not already in the setup menu, just press the MENU button
shortly to enter the setup menu ("Addr" is shown on the display)
 Now press the ENTER button for at least 5 seconds to go into
offset mode.
 Use DOWN and UP buttons to select the function that you want
to adjust:
 oPAn: used to set an offset value for the pan function.
 otIL: used to set an offset value for the tilt function.
 oCoL: used to adjust the positioning of the color wheel.
 oGob: used to adjust the positioning of the gobo wheel.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP buttons to adjust the home position
 Press the ENTER button to confirm your setting
To go back to the functions without any change press the MENU
button again.
If you want to go back to normal running mode: press the MENU button for about 2 seconds, the new offset
parameters for the different functions are preserved in flash memory.
ELECTRICAL INSTALLATION + ADDRESSING
Important: The electrical installation should be carried out by qualified personal only,
according to the regulations for electrical and mechanical safety in your country.
Electrical installation for 1 standalone unit:
 Just insert the mains cable. The unit starts working immediately in stand-alone mode.
Remark1: You can connect a CA-8 or RF-8 remote controller to the unit if you want to have more control.
Refer to "how to operate the unit" to learn how to do this.
Remark2: if there's no output, please make sure to set the unit in master mode and set the blackout mode
to "NO" and Sound State to "On" (see previous chapter)
Electrical installation for two or more units in master/slave:
In this mode the units will show a synchronized show, working to the rhythm of the beat.
 Connect 2 to maximum 16 units together using good quality balanced microphone cables. The first unit
in the chain will automatically act as the master, the other units will act automatically as slaves.
 Make sure that all units are connected to the mains.
 Done!
Remark: You can connect a CA-8 or RF-8 remote controller to the master unit if you want to have more
control over the master/slave operation
Remark2: if there's no output, please make sure to set the first unit in master mode and set the blackout
mode to "NO" and Sound State to "On" (see previous chapter)
JB SYSTEMS
®
OPERATION MANUAL
7/67
ENGLISH
Electrical installation for two or more units in DMX-master/slave:
In this mode the units will show a synchronized show, working to the rhythm of the beat but you can still
control some functions on the master by 1 or 4 DMX-channels.
 To assure proper operation you need an optional "Mini DMX-SPLITTER" (order code: 4630) to isolate
the master/slave line from the main DMX-line, see drawing.
 Connect 2 to maximum 16 units together using good quality balanced microphone cables. The first unit
in the chain will act as the master, the other units will act automatically as slaves.
 Set the master to 1MSL or 4MSL channel mode (see previous chapter). Check the DMX-chart below to
see the difference between both channel modes.
 For the DMX-controller the master and his slaves can now be considered as 1 virtual effect that needs a
start address so it can be controlled as any other DMX-unit in the DMX chain: see "DMX Address" in the
chapter "Main Menu" to see how you can set the DMX-start address.
 Make sure that all units are connected to the mains.
 Set the DMX-controller according to the DMX-chart below.
 Done!
Remark: in order to work well to the rhythm of the music, make sure that the option "Sound State" on the
master is set to "On" (see previous chapter)
DMX-Chart for 1MSL and 4MSL working modes
1 MSL
Electrical installation in DMX-mode:
 The DMX-protocol is a widely used high speed signal to control intelligent light equipment. You need to
"daisy chain" your DMX controller and all the connected units with a good quality balanced cable.
 Both XLR-3pin and XLR-5pin connectors are used, however XLR-3pin is more popular because these
cables are compatible with balanced audio cables.
Pin layout XLR-3pin:
SIRIUS JB SYSTEMS
4 MSL
Pin1 = GND ~ Pin2 = Negative signal (-) ~ Pin3 = Positive signal (+)
8/67
®
OPERATION MANUAL
SIRIUS