GEA JX7227 Instrucciones De Instalación
GEA JX7227 Instrucciones De Instalación

GEA JX7227 Instrucciones De Instalación

Kits ajustables para empotrar

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Installation
Instructions
Questions?
Call GE Answer Center at 800.626.2000 or
BEFORE YOU BEGIN
Read these instructions completely and carefully.
IMPORTANT –
instructions for local inspector's use.
IMPORTANT –
governing codes and ordinances.
Note to Installer –
instructions with the Consumer.
Note to Consumer –
future reference.
For easier installation and personal safety, we recommend
that two people install this microwave oven.
Unplug the microwave oven before attempting
installation of this kit.
FOR YOUR SAFETY:
WARNING –
installation, switch power off at service panel and lock
the service disconnecting means to prevent power from
being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten
a prominent warning device, such as a tag, to the
service panel.
TOOLS YOU WILL NEED
#2 Phillips
screwdriver
Pencil
Awl or punch
READ CAREFULLY.
KEEP THESE INSTRUCTIONS
Save these
Observe all
Be sure to leave these
Keep these instructions for
Before beginning the
Drill with
" bit or #35
7 64
Scissors (optional)
Tape measure
.
Built-In Trim Kits
JX7227 and JX7230
Visit our Website at:
Skill level – Installation of this appliance requires basic
mechanical and electrical skills.
Completion time – 1-3 hours
Proper installation is the responsibility of the installer.
Product failure due to improper installation is not
covered under the Warranty.
This kit is UL listed for installation alone or over
any General Electric/Hotpoint single electric wall oven.
PARTS INCLUDED
PART
Trim Frame
Bottom Duct
Top Bracket
Phillips Round-Head
Screws
Phillips Flat-Head
Screws
Anti-Tip Bracket
Bottom Bracket
Template
1
www.GEAppliances.com
QUANTITY
24
(21 or 22 required
for installation)
(4 required
for installation)
1
1
1
5
1
1
1

Publicidad

Tabla de contenido
loading

Resumen de contenidos para GEA JX7227

  • Página 1 Installation Built-In Trim Kits Instructions JX7227 and JX7230 Questions? Call GE Answer Center at 800.626.2000 or www.GEAppliances.com Visit our Website at: BEFORE YOU BEGIN Read these instructions completely and carefully. Skill level – Installation of this appliance requires basic mechanical and electrical skills.
  • Página 2: Installation Instructions

    Installation Instructions INSTALL BOTTOM BRACKET AND CUTOUT DIMENSIONS BOTTOM DUCT Models ” ” Fit the tab on the bottom bracket into the slot on the back of the bottom duct, and push down until the Height ” ” bracket is flush with the bottom of the duct. Fasten the bottom bracket to the bottom duct by using two Width ”...
  • Página 3 Installation Instructions INSTALL THE ANTI-TIP BRACKET INSTALL MICROWAVE OVEN INTO CABINET Draw a line on the cutout floor at the center of the Slide the microwave oven part way into the cabinet cutout, and extend the line down the face of the ”...
  • Página 4 Save or discard the extra screws. Do not place them in the microwave oven. Keep these installation instructions for future reference. Replace house fuse or close circuit breaker to restore power at the service panel. JX7227 and JX7230 49-40697 06-13 GE Printed in China...
  • Página 5: Kits Ajustables Para Empotrar

    Instrucciones Kits Ajustables para Empotrar de Instalación JX7227 y JX7230 ¿Preguntas? Llame a un Centro de Consultas de GE comunicándose al 800.626.2000 o visite nuestro sitio web en: www.geappliances.com ANTES DE COMENZAR Nivel de habilidad – La instalación de este electrodoméstico requiere un nivel básico de habilidades...
  • Página 6 Instrucciones de Instalación INSTALACIÓN DEL SOPORTE INFERIOR DIMENSIONES DEL RECORTE Y DEL CONDUCTO INFERIOR Modelos Enganche la lengüeta en el soporte inferior sobre la ranura en la parte trasera del conducto inferior, y presione hacia abajo hasta que el soporte quede alineado con la parte inferior del conducto.
  • Página 7: Instale El Soporte Antivolcaduras

    Instrucciones de Instalación INSTALE EL SOPORTE INSTALE EL HORNO MICROONDAS ANTIVOLCADURAS EN EL GABINETE Deslice la parte del horno microondas hasta la Dibuje una línea sobre el piso del recorte, mitad de la abertura del gabinete. específicamente en el centro de la misma, y Enchufe el horno microondas Doble o recorte el extremo frontal de la plantilla, Ensamble...
  • Página 8: Instalación Del Soporte Superior

    Guarde o descarte los tornillos adicionales. No los coloque en el horno microondas. Guarde estas instrucciones de instalación para referencia futura. Reemplace el fusible del hogar o cierre el disyuntor para reiniciar la corriente en el panel del servicio. JX7227 and JX7230 Impreso en China...

Este manual también es adecuado para:

Jx7230

Tabla de contenido