Fontanot 5199 Instructions De Montage página 5

obtain the same size as all others you assembled previously.
24. Fix into the floor in relation to the first baluster (C03) (H. 1190 mm - 46
5 " ) diameter bit. Use the parts C58, B12, B83 and B02 (fig. 1). Then assemble the reinforcing part (F07).
/
mm (
16
25. Find the handrail piece not marked in red colour (A13) and the one marked in red colour (A14) which will be used
for the railing of the landing (E02) (fig. 9).
26. Start to model the handrail pieces (A13) not marked in red colour, trying to give it a shape that corresponds the
nearest possible to the curve of the staircase (fig. 1).
27. Beginning from the baluster (C03) on the landing (E02), start to fasten the handrail (A13), that you have already
slightly bent in the previous operation. Use the parts C64 together with the screw driver.
Warning: position the join line of the handrail covering downwards.
28. Connect all other handrail pieces (A13), by screwing, glueing and shaping them. Use the parts B33 and D72.
29. When you reach the first baluster (C03) at the bottom of the stair, cut the excess piece of the handrail with a
hacksaw.
30. Complete the handrail (A13) by assembling the part A12. Use the parts C64 and the glue (X01) (fig. 1).
31. Insert all remaining railing balusters into the treads (L03), tighten the part B20 and fix to the handrail (A13),
paying careful attention to the vertical position. (for the stairs with a diameter larger than 140 cm (55
suggest that you first assemble the shorter balusters) (fig. 10). According to the geometrical characteristics of
the staircase, the intermediate balusters may protrude from the lower part of the step, in which case we advise
cutting them off level with the step to obtain a more attractive finish.
32. Check again the regular shape of the handrail (A13) and, if necessary, correct it with a rubber hammer.
33. Complete the railing assembly by fitting the parts B82 into the lower part of the balusters (C03) and the parts
C19 into the lateral part of the treads (fig. 1).
Assembly of the Balustrade
34. Screw the baluster (C04) into the part G01 that sticks out from the landing (E02) (fig. 8).
35. Set the parts F01, by using the parts C58, B83, B02 onto the landing (E02). Pierce with the 5 mm (
the landing (E02), maintaining a similar distance between the holes as the one between the already assembled
railing balusters (C03).
36. Set the shorter balusters C03 (H. 935 mm - 36
37. Fix the part A15 into the baluster (C04), by using the part B02 (fig. 1).
38. Fix the handrail (A14) marked in red colour, using the parts C64 (fig. 1).
39. In case there were walls around the stair well and on their position, it could be necessary to position one or two
more balusters C03 (H. 935 mm - 36
40. In that case it is necessary to consider either the distance between all other balusters, or otherwise the
distance from the wall. For the fixing it is suggested to pierce the landing (E02) with the 5 mm (
and to use the fixing parts F01, C58, B83, B02. Whereas for the fixing into the floor it is suggested to pierce the
floor with the 12 mm (
the landing baluster to the floor- mounted baluster, (fig. 10), shape the handrails carefully, following the curves.
If wrinkles should form on the inside of the handrails, this is not a defect. Rubbing the area energetically with a
paper napkin (to generate heat) will cause them to disappear.
Final Assembly
41. In order to re-inforce the staircase at the intermediate points, you must fix into the wall the parts F09 and
connect them to the balusters (C03) by means of the parts F08. Pierce the wall with the 8 mm (
use the parts C50, C49, C58, B12 (fig. 12).
" ) (fig. 10).
13 /
16
" ) drill bit and to use the parts F01, B02, B87 (fig. 11). In case it is necessary to join
15
/
32
" ) and tighten the part B02 (fig. 1)
13 /
16
www.arkestairs.com
5 - kl
" ), the part F01, by piercing with the 8
7 /
8
" ), we
1 /
8
" ) drill bit
13 /
64
13 " ) drill bit
/
64
" ) drill bit and
5 /
16