Declaration Of Conformity - Carson EXPERT 3 Instrucciones De Uso

Ocultar thumbs

Contenido

página de 12

/ 12
Contenido
Tabla de contenido
Marcadores

Tabla de contenido

Idiomas disponibles

SPECIFICATION

Input: 230V~50Hz OR 12V car battery 12.6V DC

Outputs:

OUTPUT sockets:

adjustable by means of a slide switch)

Balancer: maximum - 140mA per cell

Transmitter: 150mA

Receiver: 150mA

Charging indicators: 3 LEDs RED fast charge

transmitter (150mA)

receiver (150mA)

Power indicator: LED YELLOW

Discharge: LED GREEN

Protection: Each output has a short-circuit and

over voltage protection

Over charging protection for output socket

SAFETY MEASURES AND PRECAUTIONS

• The charger must be protected against high humidity

and water.

• Do not operate charger at environment temperature

higher than 40°C

• Do not fast charge a hot battery pack - let it cool down

naturally before starting the next charging process.

• Do not cover the cooling slots. The unit can get very

warm during charging.

• Allow the charger to cool down after two fast charging

cycles 4A or 2A.

• For NiCd/NiMH batteries do not recharge the battery

pack unless it is completely discharged.

• Never leave the charger unattended!

• If the battery gets hot (>45"C) remove it from the

charger immediately. Otherwise, it may cause risk

and explosion! When the battery pack has reached a

temperature of 45°C, it must be considered as fully

charged. Do not charge a hot battery.

• Charge only NiCd, NiMH, LiPo or LiFe batteries. Do not

attempt to charge lead-acid and Li-Ion batteries or

primary disposable cells.

• Make sure to select correct mode before charge.

Charging with wrong mode may cause risk and

explosion!

• Connect the charger only to appropriate voltage sources

(230V~50Hz mains socket or 12V DC cigarette lighter

socket).

• Never connect the charger to the 230V~50Hz socket

AND the 12V DC socket at the same time, otherwise it

will be damaged.

• Repairs may only be carried out by authorized service

centres.

• CAUTION! Explosive gases, avoid open fire and sparks!

• Keep the charger out of the reach of children.

• Never plug in the charger if there are any signs of

damage to the housing, cables, connectors or mains

plug. Never try to open the charger.

• Set the fast charge current 1A - 2A - 4A, according to

the user manual.

Service-Hotline:

(8.00 Uhr -17.00 Uhr)

(01805) 73 33 00

14 ct/min

- 0% / +15%

1A-2A-4A (fast charge

PLEASE NOTE WHEN USING LiPo / LiFe

BATTERIES

LiPo/LiFe batteries are particularly vulnerable to

excessively deep discharge or overcharging. Both deep

discharge and overcharge damage the battery

permanently and also pose a significant fire hazard.

• To charge the LiPo/LiFe battery, remove it from the

model and place it on a non-flammable surface, never

on a car seat or in the boot, for instance.

• CAUTION!

For LiPo batteries always put the switch in position

"LiPo"

• For LiFe batteries always put the switch in position

"LiFe".

For LiPo or LiFe batteries never switch on "discharge".

• In LiPo batteries with more than one cell, a voltage

imbalance may build up between the individual cells

after several charges. This can lead to a premature

reduction in power. To avoid this, the imbalance can be

equalised by using the charger built-in balancer.

• Always

disconnect LiPo or LiFe batteries from the

carging cable

together with the balancer socket.

DISPOSAL

Please note and understand the symbols on this product,

packaging or instructions. Electronic components are

valuable materials and at the end of their useful life should

not be disposed with household waste! Help

us to protect the environment and safeguard

our resources by discarding this equipment at

a dedicated recycling point. The authority

responsible for waste disposal or your retailer

will be able to answer any questions you may

have in this aspect.