TFA 60.2520 Instrucciones Para El Manejo página 8

TFA_No. 60.2520_Anleitung_01_13
TOUCH
– Radio-controlled alarm clock
• Inside ferro-concrete rooms (basements, superstructures), the
received signal is naturally weakened. In extreme cases, please
place the unit close to a window to improve the reception.
• During nighttime, the atmospheric interference is usually less
severe and reception is possible in most cases. A single daily recep-
tion is adequate to keep the accuracy deviation below 1 second.
7. Operation
• The instrument will automatically quit the setting mode if no
button is pressed within 5 seconds.
• Press and hold + or - button in the setting mode for fast running.
• Each button operation is acknowledged with a beep.
• After completing the entries a short beep will sound twice in fast
succession.
7.1 Manual setting of the clock and calendar
• Press and hold MODE/SET button in normal mode.
• The year digit flashes. Press the + or - buttons to adjust the year.
• Press the MODE/SET button again and the setting sequence is
shown as follows: Day and month, the date, month/day sequence
(American version) or day/month (European version), the minutes
and the hours, the 12 (AM or PM appears on the display) and the
24 hours system indication and the time zone. Press the + or -
button to adjust them.
• The time zone (+3/-3) setting is needed for countries where the
DCF signal can be received but the time zone is different from
the DCF time (e.g. +1=one hour later).
• Confirm with MODE/SET button.
• The display shows the current time.
• The day-of-week (MON, TUE, WED, THU, FRI, SAT or SUN appears on
the display) will be calculated automatically after setting the date.
• The manually set time will be overwritten by the DCF time when
the signal is received successfully (Precondition: reception func-
tion ist not "OFF"). In the display appears OK above the DCF
reception button.
7.2 Setting of the alarm
• Press and hold ALARM button.
• The alarm symbol, ALARM and the indication of the day-of-week
appear in the display.
• The indication of the alarm time flashes.
• Press the + or - button to adjust the desired alarm time (minutes
and hours).
• Press the MODE/SET button.
14
05.02.2013 15:30 Uhr Seite 8
TOUCH
– Radio-controlled alarm clock
• The indication of the day-of-week flashes.
• Press the + or – button to choose if the adjusted alarm time
should be activated for:
Monday until Sunday
(MON, TUE, WED, THU, FRI, SAT, SUN appear on the display)
Monday until Friday
(MON, TUE, WED, THU, FRI appear on the display)
Saturday and Sunday
(SAT, SUN appear on the display)
• Confirm the setting with the MODE/SET button.
• The alarm time and the current time appear on the display.
• The alarm is activated.
• To deactivate/activate the alarm function press the ALARM button.
• The alarm symbol disappears/appears on the display.
• Once the alarm starts to ring, the alarm symbol flashes.
• Press any button to stop the alarm or press the top of the instru-
ment (SNOOZE/LIGHT) to activate the snooze function.
• The alarm symbol flashes and the backlight will be activated for
few seconds.
• The alarm will be interrupted for 5 minutes.
7.3 Display
• Press the MODE/SET button in normal mode. The time, the day
and the month and the year appear in sequence on the display.
• Press the + or - button in normal mode. The alarm time with the
activated day-of-week appear on the display.
7.4 Backlight
• Press the top of the instrument (SNOOZE/LIGHT) and the back-
light will be activated for 5 seconds.
• Press the light button to use the automatical backlight.
• Automatic backlight is activated.
• Automatic backlight is disabled.
• If the automatic backlight is activated it switches on automatically
at 10 pm and switches off again at 6 am.
8. Care and maintenance
• Clean it with a soft damp cloth. Do not use solvents or scouring
agents.
• Remove the batteries if you do not use the product for a lengthy
period.
• Keep the instrument in a dry place.
15