Before Starting The Equipment; Operation; Cleaning, Maintenance And Ordering Of Spare Parts - EINHELL TE-AP 750 E Manual De Instrucciones

Sierra sable/sierra universal
Ocultar thumbs Ver también para TE-AP 750 E:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Do not overload the appliance.
Have the appliance serviced whenever ne-
cessary.
Switch the appliance off when it is not in use.
Wear protective gloves.
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
Limit the operating time.
All stages of the operating cycle must be conside-
red (for example, times in which the electric tools
are switched off and times in which the tool is
switched on but operates without load).

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
5.1 Changing the saw blade (Fig. 2)
Always switch off and unplug the multi-saw before
working on the machine or changing the saw
blade.
Turn the ring (a) on the blade holder (5) as shown
in Fig. 2 until the blade (3) lets itself be slipped
into the slot of the blade holder (5).
When you now let go of the ring (a) again, the ring
(a) should return to its starting position.
If this fails to happen, try turning the ring (a) by
hand into its starting position.
Pull on the blade to check whether it sits tightly in
the holder.
Anl_SA_TE_AP_750_E_SPK8.indb 25
Anl_SA_TE_AP_750_E_SPK8.indb 25
GB
5.2 Adjusting the soleplate (Fig. 3)
Warning!
Pull out the power plug.
To adjust the soleplate (4), open the locking lever
(6) on the right-hand side in order to unlock the
soleplate (4). Set the required distance and close
the lever (6) again.
Check that the soleplate is secure!

6. Operation

6.1 ON/OFF switch (Fig. 1/Item 1)
To switch on:
Press the ON/OFF switch
To switch off :
Release the ON/OFF switch
6.2 Locking button (Fig. 1/Item 2)
You can lock the ON/OFF switch (1) using the lo-
cking button (2) when the equipment is in operati-
on. To switch off the equipment briefl y hold down
the ON/OFF switch (1).
6.3 Use as a jigsaw (Fig. 4)
Place the multi-saw on the material to be cut as
shown in Fig. 4. Switch on the multi-saw and push
it along against the material to be cut. Adapt your
cutting speed to the material.
6.4 Status indicator (Fig. 1/Item 7)
The status indicator (7) lights up when the power
plug is connected.
7. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the mains power plug before star-
ting any cleaning work.
7.1 Cleaning
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
We recommend that you clean the device
immediately each time you have finished
using it.
- 25 -
18.02.2019 13:43:12
18.02.2019 13:43:12

Publicidad

Capítulos

Tabla de contenido
loading

Tabla de contenido