Sunex Tools SX210 Instrucciones De Operación página 2

Mini esmeril angular 4"
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

FAILURE TO OBSERVE THESE WARNINGS
This insTrucTion Manual conTains
iMporTanT safeTy inforMaTion.
read This insTrucTion Manual carefully
and undersTand all inforMaTion Before
operaTing This Tool.
• Always operate, inspect and maintain this
tool in accordance with American National
Standards Institute Safety Code of Portable
Air Tools (ANSI B186.1) and any other
applicable safety codes and regulations.
• For safety, top performance and maximum
durability of parts, operate this tool at 90 psig
6.2 bar max air pressure with 3/8" diameter
air supply hose.
• Always
and face protection when operating or
performing maintenance on this tool.
Always wear hearing protection when using
this tool.
• High sound levels can cause permanent
hearing loss. Use hearing protection as
recommended by your employer or OSHA
regulation.
• Keep the tool in efficient operating
condition.
• Operators and maintenance personnel must
be physically able to handle the bulk, weight
and power of this tool.
• Air under pressure can cause severe
injury. Never direct air at yourself or others.
Always turn off the air supply, drain hose
of air pressure and detach tool from air
supply before installing, removing or
adjusting
or before performing any maintenance on
this tool. Failure to do so could result
in injury. Whip hoses can cause serious
injury. Always check for damaged, frayed
or loose hoses and fittings, and replace
immediately. Do not use quick detach
couplings at tool. See instructions for correct
set-up.
• Air
powered
use. Vibration, repetitive motions or
uncomfortable positions over extended
periods of time may be harmful to your
hands and arms. Discontinue use of tool if
discomfort, tingling feeling or pain occurs.
Seek medical advice before resuming use.
SX210: Parts Breakdown & Operating Manual
COULD RESULT IN INJURY
wear
impact-resistant
any accessory on this tool,
tools
can
vibrate
• Place the tool on the work before starting the
tool. Do not point or indulge in any horseplay
with this tool.
• Slipping, tripping and/or falling while
operating air tools can be a major
cause of serious injury or death. Be
aware of excess hose left on the walking or
work surface.
• Keep body working stance balanced and
firm. Do not overreach when operating
the tool.
• Anticipate and be alert for sudden changes
in motion during start up and operation of
any power tool.
eye
• Do not carry tool by the hose. Protect the
hose from sharp objects and heat.
• Tool shaft may continue to rotate briefly
after throttle is released. Avoid direct
contact with accessories during and
after use. Gloves will reduce the risk of cuts
or burns.
• Keep away from rotating end of tool.
Do not wear jewelry or loose clothing.
Secure long hair. Scalping can occur
if hair is not kept away from tool and
accessories.
neckwear is not kept away from tool
and accessories.
• Correct grinding wheel mounting is necessary
to prevent injury from broken wheels. Do
not use chipped or cracked grinding wheels.
Grinding wheels should be a free fit on the
spindle to prevent stress at the hole. Use
only wheel collars that come with the grinder
for mounting the grinding wheel. Flat washers
or other adapters may over stress the wheel.
Always use heavy paper blotter discs between
the wheel collars and the grinding wheel.
Tighten the wheel on the spindle to prevent
spin off when the air grinder is turned off.
• Do not lubricate tools with flammable or
volatile liquids such as kerosene, diesel or
jet fuel.
in
• Do not force tool beyond its rated capacity.
• Do not remove any labels. Replace
any damaged labels.
• Use
Sunex Tools.

Choking
can
accessories
recommended
rev. 04/8/06
occur
if
by

Publicidad

Tabla de contenido
loading

Tabla de contenido