Air Supply - Sunex Tools SX210 Instrucciones De Operación

Nipple
Air Supply
Tools of this class operate on a wide range of air pressures. It is
recommended that air pressure of these tools measures 90 PSI at the
tool while running free. Higher pressure (over 90 psig; 6.2 bar) raises
performance beyond the rated capacity of the tool which will shorten
tool life because of faster wear and could cause injury.
Always use clean, dry air. Dust, corrosive fumes and/or water in the
air line will cause damage to the tool. Drain the air tank daily. Clean the air
inlet filter screen on at least a weekly schedule. The recommended hookup
procedure can be viewed in the above figure.
The air inlet used for connecting air supply, has standard 1⁄4" NPT.
Line pressure should be increased to compensate for unusually long
air hoses (over 25 feet). Minimum hose diameter should be 3/8" I.D.
and fittings should have the same inside dimensions and be tightly
secured.
Lubrication
Lubricate the air motor daily with quality air tool oil. If no air line
oiler is used, run a teaspoon of oil through the tool. The oil can
be squirted into the tool air inlet or into the hose at the nearest
connection to the air supply, then run the tool.
LIMITED WARRANTY...
SUNEX INTERNATIONAL, INC. WARRANTS TO ITS CUSTOMERS THAT THE COMPANY'S SUNEX TOOLS
PRODUCTS ARE FREE FROM DEFECTS IN WORKMANSHIP AND MATERIALS.
Sunex International, Inc. will repair or replace its Sunex Tools
workmanship or materials, based upon the terms and conditions of the following described warranty plans attributed to that specific product.
This product carries a ONE YEAR warranty. During this warranty period, Sunex Tools will repair or replace at our option any part or unit which
proves to be defective in material or workmanship.
Other important warranty information...
This warranty does not cover damage to equipment or tools arising from alteration, abuse, misuse, damage and does not cover any repairs or
replacement made by anyone other than Sunex Tools or its authorized warranty service centers. The foregoing obligation is Sunex Tools' sole
liability under this or any implied warranty and under no circumstances shall we be liable for any incidental or consequential damages.
Note: Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may
not apply to you. Please contact your local Sunex distributor for proper warranty handling procedures.
If you have any questions about warranty service, please write to Sunex Tools. This warranty gives you specific legal rights and you may also
have other rights which vary from state to state. Repair kits and replacement parts are available for many of Sunex Tools products regardless
of whether or not the product is still covered by a warranty plan.
Shipping Address: Sunex Tools • 315 Hawkins Rd. • Travelers Rest, SC 29690
Mailing Address: Sunex Tools • P.O. Box 4215 • Greenville, SC 29608
SX210: Parts Breakdown & Operating Manual
Operation
• Always use the recommended wheel guard to
prevent injury from broken grinding wheel parts.
If a guard has withstood a wheel breakage,
discontinue its use and replace it with a new
guard. It may be damaged. Position the guard
between the grinding wheel and the operator. Use barriers to
protect others from wheel fragments and grinding sparks.
• Always wear impact-resistant eye and face
protection when involved in the operation of this
tool. Even small projectiles can injure eyes and
cause blindness. A grinding wheel that bursts
can cause very serious injury. Daily measure
the air grinder speed with a tachometer to make sure it's not
greater than the RPM marked on the grinding wheel. Never use
a grinding wheel marked with a speed lower than the air grinder
speed.
• Before grinding, test grinding wheel by briefly running the tool
at full throttle. Be sure to use a barrier (such as under a heavy
work table) to stop any possible broken wheel parts.
®
branded products which fail to give satisfactory service due to defective
4
®
BRANDED
rev. 04/8/06