Troubleshooting - HAMPTON BAY 413-855 Manual De Instrucciones

INSTALLATION OF LAMP (BULB)
1. WARNING: Turn off power and allow fixture to cool down 20 minutes prior to
replacing JCD lamp (bulb). Never use a lamp with a higher wattage than the stated
maximum (40 Watt) allowed on the fixture. Using a higher wattage lamp may
cause a fire hazard and/or damage to the unit.
2. When replacing the lamp (bulb), use only a G8 JCD type, halogen 40-Watt lamp
(bulb) of the same size.
3. ALWAYS handle JCD halogen lamps (bulbs) with gloves or a soft cloth.
See FIGURE 2. NEVER touch the lamp (bulb) with your bare hands as the oil
from your hand may cause the lamp (bulb) to fracture when illuminated.
4. Open the coach light door by pulling locking pin up, then gently swing door open
to expose inside of fixture.
5. Insert 40-Watt JCD by aligning the lamp (bulb) prongs with the socket and gently
push the lamp (bulb) straight in until properly seated.
MOTION SENSOR
Observe the two controls on the bottom of the motion sensor – FIGURE 3.
The time setting for the motion light is on the left as indicated by the symbol.
The 'Flame' light setting is on the right as indicated by the symbol.
– ON: 'Flame' light will remain ON at all times.
AUTO: 'Flame' light will be controlled by the photocell, turning ON at dusk
and OFF at dawn.
– 10, 5, 1: Sets how long the light will stay on after motion is detected (1, 5, or
10 minutes). Slide the switch to the desired time duration.
TEST: Allows the motion sensor to activate during daylight for 5 seconds,
then off for 5 seconds to standby for another testing.
The Motion Indicator Light will glow red when motion has been detected. NOTE: If the
Motion Indicator Light is on but the JCD bulb is not on, check the bulb for replacement.

TROUBLESHOOTING

REMEDY
SYMPTOM
1. Make sure the switch (if applicable) is ON.
Does not function at all.
2. Check that the circuit breaker, fuse and main power switch is on.
3. Be sure sensor is pointed to target area.
4. Check lamp (bulb) for damage.
Light cycles ON and Confirm motion sensor is directed away from heat sources such as street, active sidewalk, barbeque grill, etc.
OFF.
If fixture continues to fail to operate properly, check to make sure the line voltages at the fixture is correct, the fixture is wired correctly, and
that the fixture is grounded as noted above.
QUESTIONS: For further assistance or more information,please call 1-800-562-5625, 8 am – 5 pm (Pacific Time), Monday – Friday.
LIMITED LIFETIME WARRANTY – This product is warranted to be free from defects in material and workmanship for life of product. If a defect occurs, call 1-800-562-5625
for instructions on how to have defective product repaired or replaced free of charge. LIMITATIONS - This warranty only covers the assembled lighting products and accessories
and is not extended to other components, Lamp Bulb(s), or equipment used on the product. Warranty extends to original purchaser of product. Receipt or other approved proof of
purchase required for warranty service. NOT LIABLE FOR INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES. Some states do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state. NOT COVERED - Product failure not relating to faulty material or workmanship, corrosion of brass components, reimbursement for
installation or unauthorized service.
Hampton Products International Corp.
50 Icon, Foothill Ranch, CA 92610-3000 USA
www.hamptonproducts.com • 1-800-562-5625
Figure 2
Socket
H - 40 Watt JCD
Figure 3
Photo Eye
10 5 1 TEST AUTO
Made in China
© 2011 Hampton Products International Corp.
999-60815_HB2105BZ_REVB 8/11
Motion
Indicator
Light
ON