General Safety Instructions For Handling Power Tools (European Locations) - I-DRILL 2i-drill Manual Del Usuario

Specifications
Motor: 12 V– . ..
Low speed: n -Lo = 0 – 350min
-1
0
High speed: n -Hi = 0 – 1200 min -1
0
Max. soft/hard torque: 10/25 Nm
Drill diam Ø: - Wood 20 mm
GB
- Steel 8 mm
Screw diam Ø: max 8 mm
Chuck: 0,8 – 10 mm
Battery: 12 V– . .. /1300 mAh/Li-Ion
model number id12BL1
Charger type: Model id12CHPPL1
Input: 100 – 240Vac
50/60Hz 28W
Output: 14V dc 2.0 A
Charging time: Approx 45 – 60 Min.
Vibration data: a =0.84m/s
2
w
when screwdriving: 1.143m/s
2
when boring: 1.562 m/s 2
Noise emission/vibration
Noise emission LPA: 65 dB(A)
LWA: 76 dB(A)
Measuring inaccuracy: KpA: 3 dB(A)
KwA: 3 dB(A)
General safety instructions for handling
power tools (European locations)
WARNING. Read all safety warnings and
all instructions.
Failure to follow the warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains
operated (corded) power tool or battery-operated (cordless)
power tool.
This unit may not be used by people (including children) with
reduced physical, sensory or mental capacities, with a lack
of experience and without the appropriate knowledge, unless
they are supervised by someone who is responsible for their
safety or have been instructed by such a person with regard
to how the unit is to be operated.
Children should be supervised to ensure that they do not
play with the device.
1. Work area
a. Keep work area clean and well lit. Cluttered and dark
areas invite accidents.
b. Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
c. Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose control.
2. Electrical Safety
a. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce
risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
4
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
the risk of electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric
shock.
f. If it is not possible to avoid using the electrical
tool in a damp environment, use a residual current
circuit-breaker. The use of a residual current circuit-
breaker reduces the risk of an electrical shock.
3. Personal safety
a. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or medication.
A moment of inattention while operating power tools may
result in serious personal injury.
b. Use personal protective equipment. Always wear
eye protection. Protective equipment such as dust
masks, nonskid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce
personal injuries.
c. Prevent unintentional starting. Ensure the switch
is in the offposition before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your finger on the
switch or energising power tools that have the switch
on invites accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to
a rotating part of the power tool may result in personal
injury.
e. Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power tool
in unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g. Keep handles dry, clean and free from oil and
grease. Slippery handles do not allow for safe handling
and control of the tool in unexpected situations.
h. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of these devices
can reduce dust related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power tool
for your application. The correct power tool will do the job
better and safer at the rate for which it was designed.
b. Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source before
making any adjustments, changing accessories, or
storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool's
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
5
GB