General Safety Precautions; Ec Declaration Of Conformity; Machinery Directive - DITEC QIK4-7 Manual Para La Instalacion Y La Manutencion

GENERAL SAFETY PRECAUTIONS

GB
This installation manual is intended for professionally
competent personnel only.
Installation, electrical connections and adjustments must be per-
formed in accordance with Good Working Methods and in com-
pliance with applicable regulations. Before installing the product,
carefully read the instructions. Bad installation could be hazardous.
The packaging materials (plastic, polystyrene, etc.) should not
be discarded in the environment or left within reach of children,
as these are a potential source of hazard. Before installing the
product, make sure it is in perfect condition.
Do not install the product in an explosive environment and atmo-
sphere: gas or inflammable fumes are a serious hazard risk.
Before installing the motors, make all structural changes relating
t o safety clearances and protection or segregation of all areas
where there is risk of being crushed, cut or dragged, and danger
areas in general.
Make sure the existing structure is up to standard in terms of
strength and stability.
The motor manufacturer is not responsible for failure to use
Good Working Methods in building the frames to be motorised
or for any deformation occurring during use.
The safety devices (photocells, safety edges, emergency stops,
etc.) must be installed taking into account: applicable laws and
directives, Good Working Methods, installation premises, system
operating logic and the forces developed by the motorised door
or gate.
The safety devices must protect any areas where the risk exists
of being crushed, cut or gragged, or where there are any other
risks generated by the motorised door or gate. Apply hazard
area notices required by applicable regulations.
Each installation must clearly show the identification details of
the motorised door or gate.
Before making power connections, make sure the plate
details correspond to those of the power mains.
Fit an omnipolar disconnection switch with a contact opening
gap of at least 3 mm. Make sure an adequate residual current
circuit breaker and overcurrent cutout are fitted upstream of
the electrical system. When necessary, connect the motorised
door or gate to a reliable earth system made in accordance with
applicable safety regulations. During installation, maintenance
and repair, interrupt the power supply before opening the lid to
access the electrical parts.
To handle electronic parts, wear earthed antistatic con-
ductive bracelets.
The motor manufacturer declines all responsibility in the event
of component parts being fitted that are not compatible with the
safe an correct operation.
For repairs or replacements of products only original spare parts
must be used.
The installer shall provide all information relating to automatic,
manual and emergency operation of the motorised door or gate,
and provide the user with operating instructions.

MACHINERY DIRECTIVE

The installer who installs and sets in motion a door or motorised
gate in his name becomes the manufacturer, according to the
Machine Directive (98/37/EC) and, as such, must: prepare the
technical file, draw up the EC conformity declaration, attach
the EC mark.
For further information, see the "EC Guidelines" available on the
Internet at the following address: www.ditec.it
QIK4-7 - IP1861
OPERATING INSTRUCTIONS
QIK4E
Service class: 4 (minimum 10÷5 years of working life with
100÷200 cycles per day)
Applications: INTENSE (for condominial, industrial and
commercial entrances, parking spaces with intense vehicle or
pedestrian access)
QIK7EH
Service class: 5 (minimum 5 years of working life with 600
cycles per day)
Applications: HIGHLY INTENSE (for collective entrances with
particularly intense vehicle or pedestrian access)
- Performance characteristics are to be understood as referring
to the recommended weight (approx. 2/3 of maximum per-
missible weight). When used with the maximum permissible
weight a reduction in the above mentioned performance can
be expected.
- Service class, running times, and the number of consecutive
cycles are to be taken as merely indicative Having been statisti-
cally determined under average operating conditions, and are
therefore not necessarily applicable to specific conditions of
use. During given time spans product performance characteri-
stics will be such as not to require any special maintenance.
- Each automatic entrance has variable elements such as:
friction, balancing and environmental factors, all of which
may substantially alter the performance characteristics of the
automatic entrance or curtail its working life or parts thereof
(including the automatic devices themselves). The installer
should adopt suitable safety conditions for each particular
installation.

EC DECLARATION OF CONFORMITY

Manufacturer: DITEC S.p.A.
Address: Via Mons. Banfi, 3
21042 Caronno P.lla (VA) - ITALY
Declares that the motorized barrier product, such as QIK4-7
conforms to the essential requisites of the following EC
directives:
- Electromagnetic Compatibility Directive 2004/108/EC
- Machine Directive 98/37/EC
- Building Products Directive 89/106/EC
conforms to the following characteristics of the standard EN
13241-1 (Attachment ZA):
- production controls in the factory (in conformity)
- release of dangerous substances (in conformity)
- resistance to wind load (class 5)
- safe opening (in conformity)
- mechanical resistance and stability (in conformity)
- manoeuvring forces (in conformity)
Organisation notified: Treviso Tecnologia - CERT
Registration number: 1600
Address: Via Pezza Alta, 34
31046 Rustignè di Oderzo (TV)
Caronno Pertusella,
28-09-2006
10
Fermo Bressanini
(President)