Makita XRM11 Manual De Instrucciones página 8

NOTE:
Depending on the conditions of use and the ambient
temperature, the indication may differ slightly from the
actual capacity.
Using supplied AC power adaptor
Remove the rubber protector and insert the adaptor
plug into the DC socket on the right hand side of the
speaker. Plug the adaptor into a standard mains socket
outlet. Whenever the adaptor is used, the battery pack is
automatically disconnected.
CAUTION:
● Always disconnect the AC power adaptor
completely before moving the speaker. If the AC
adaptor is not removed, it may cause an electric
shock.
● Never pull and/or drag the cord of the adaptor.
If not, the speaker may accidentally fall down,
causing injury to you or someone around you.
IMPORTANT:
● The mains adaptor is used as the means of connecting
the speaker to the mains supply. The mains socket
used for the speaker must remain accessible during
normal use.
● In order to disconnect the speaker, the mains adaptor
should be removed from the mains outlet completely.
● Use the AC power adaptor supplied with the product or
specified by Makita only.
● Do not hold the power supply cable and plug by your
mouth. Doing so might cause an electric shock.
● Do not touch the power plug with wet or greasy hands.
● Damaged or entangled cords increase the risk of
electric shock. If the cord is damaged, have it replaced
by our authorized service center in order to avoid a
safety hazard. Do not use it before repair.
● After use, always store AC power adaptor out of the
reach of children. If Children play with the cord, they
may suffer injury.
USB power supply socket
This jack can be used to charge a mobile phone or any
other device that uses less than 2.1A of DC current.
Charging will only occur when the speaker is switched on.
NOTE:
Ensure the specification of your external device such as
mobile phone or player is compatible with the speaker.
Please read instruction manual of your external device
before charging.
IMPORTANT:
● Before connecting USB device to the charger, always
backup your data of USB device. Otherwise your data
may lose by any possibility.
● The charger may not supply power to some USB
devices.
● When not using or after charging, remove the USB
cable and close the cover.
● Do not connect power source to USB port. Otherwise
there is risk of fire. The USB port is only intended for
charging lower voltage device. Always place the cover
onto the USB port when not charging the lower voltage
device.
● Do not insert a nail, wire, etc. into USB power supply
port. Otherwise a circuit short may cause smoke and
fire.
● Do not connect this USB socket with your PC USB port,
as it is highly possible that it may cause breakdown of
the units.
LISTENING TO MUSIC VIA
BLUETOOTH STREAMING
You need to pair your Bluetooth device with the speaker
before you can auto-link to play/stream Bluetooth music
through the speaker. Pairing creates a 'bond' so two
devices can recognize each other.
Note:
To have the better sound quality, we recommend setting
the volume to more than two-thirds level on your Bluetooth
device and then adjust the volume on the speaker as
required.
Pairing your Bluetooth device for the
first time
1. Press the Power button to turn on the speaker. "Pairing"
will appear on the display to show the speaker is
discoverable.
2. Activate Bluetooth on your device according to the
device's user manual to link to the speaker. Locate
the Bluetooth device list and select the device named
"XRM11" (With some mobiles which are equipped with
earlier versions than BT2.1 Bluetooth device, you may
need to input the pass code "0000").
3. Once connected, there will be a confirmation tone
sound. "Paired" will appear on the display. You can
simply select and play any music from your source
device. Volume control can be adjusted from your
source device, or directly from the speaker.
4. Use the controls on your Bluetooth-enabled device or
on the speaker to play/pause and navigate tracks.
Note:
● If 2 Bluetooth devices, pairing for the first time, both
search for the speaker, it will show its availability on
both devices. However, if one device links with this unit
first, then the other Bluetooth device won't find it on the
list.
● If your Bluetooth device is temporarily disconnected to
the speaker, then you need to manually reconnect your
device again to the speaker.
8 ENGLISH