Service Parts - Broan QTR Serie Manual De Instrucciones
Ocultar thumbs
Ver también para QTR Serie:
- Manual de instrucciones (12 páginas) ,
- Manual de usuario (9 páginas) ,
- Guia de inicio rapido (9 páginas)
Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
INSTALL GRILLE
5. Finish ceiling.
Install ceiling material. Cut out around housing.
6. Attach
grille to
housing.
Squeeze grille
springs and
insert them
into slots on
each side of
housing.
7. Push
grille
against
ceiling.
8. Remove
light lens.
Carefully
insert a small
flat-blade
screwdriver
betweeen
grille and lens.
Pry lens out.
9. Install light
bulbs.
Fluorescent
bulb supplied
with "FLT"
models.
Purchase an
incandescent
bulb for "L"
Fluorescent bulb shown
models - 100W
Max.
Purchase a 4W incandescent night light bulb.
Insert bulbs into their sockets. Replace lens.
MODELS QTR080L • QTRE080FLT •
SERVICE PARTS
Key No.
Part No.
1
97016466
Housing
2
97016449
Duct Connector-4"
3
98010102
Wiring Plate
4
99170245
Screw, #8-18 X .375 (2 req'd)
5
97016933
Wire Panel/Harness Assembly
6
99020284
Blower Wheel
7
99080568
Motor (QTR080L)
99080562
Motor (QTRE080FLT)
99080582
Motor (QTR110L)
99080580
Motor (QTRE110FLT)
8
99100491
Isolator (4 req'd)
9
97016467
Motor Plate (QTR080L, QTR110L)
97016901
Motor Plate (QTRE080FLT, QTRE110FLT)
10
99250959
Washer #8 (4 req'd)
11
99260558
Nut, Hex Lock #8-32 (4 req'd)
*
97016621
Blower Assembly (QTR080L)
*
97016905
Blower Assembly (QTRE080FLT)
*
97016739
Blower Assembly (QTR110L)
*
97016906
Blower Assembly (QTRE110FLT)
12
97016546
Grille Assembly (QTR080L, QTR110L)
97016868
Grille Assembly (QTRE080FLT, QTRE110FLT)
13
99140199
Grille Spring (2 req'd)
14
99111281
Lens
15
97016888
Bulb, 42W Fluorescent (QTRE080FLT, QTRE110FLT)
16
97016864
Ballast Assembly (QTRE080FLT, QTRE110FLT)
17
99260423
Nut, Hex #8-32 (2 req'd) (QTRE080FLT, QTRE110FLT)
18
99111293
Spacer (2 supplied)
19
QTHB1
Hanger Bar Kit
Order service parts by "Part No." - not by "Key No."
QTR110L • QTRE110FLT
TAB
Description
(includes key nos. 6 thru 11)
(includes key nos. 13 & 14)
Page 4
Replacement parts can
be ordered on our
website. Please visit us
at www.broan.com
SERVICE NOTE
To remove Blower
Assembly:
Unplug motor (7).
Remove screw (4) from
motor plate (9) flange.
Find the single TAB on
the motor plate (located
next to the receptacle).
Push up near motor plate
tab while pushing out on
side of housing. Or insert
a straight-blade
screwdriver into slot in
housing (next to tab) and
twist screwdriver.
99043845A
Publicidad
Tabla de contenido
