Descargar Imprimir esta página
Broan QTR100FLT Manual Del Usuario
Broan QTR100FLT Manual Del Usuario

Broan QTR100FLT Manual Del Usuario

Ventilador / lámpara / lámpara de noche

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

MODEL QTR100FLT
FAN / LIGHT / NIGHT LIGHT
READ AND SAVE THESE INSTRUCTIONS
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR IN-
JURY TO PERSONS, OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the manufacturer.
If you have questions, contact the manufacturer at the address
or telephone number listed in the warranty.
2. Before servicing or cleaning unit, switch power off at service
panel and lock the service disconnecting means to prevent
power from being switched on accidentally. When the ser-
vice disconnecting means cannot be locked, securely fasten
a prominent warning device, such as a tag, to the service
panel.
3. Installation work and electrical wiring must be done by a
qualified person(s) in accordance with all applicable codes
and standards, including fire-rated construction codes and
standards.
4. Sufficient air is needed for proper combustion and exhausting
of gases through the flue (chimney) of fuel burning equip-
ment to prevent backdrafting. Follow the heating equipment
manufacturer's guideline and safety standards such as those
published by the National Fire Protection Association (NFPA),
and the American Society for Heating, Refrigeration and Air
Conditioning Engineers (ASHRAE), and the local code authori-
ties.
5. When cutting or drilling into wall or ceiling, do not damage
electrical wiring and other hidden utilities.
6. Ducted fans must always be vented to the outdoors.
7. Acceptable for use over a tub or shower when connected to
a GFCI (Ground Fault Circuit Interrupter) - protected branch
circuit.
8. This unit must be grounded.
CAUTION
1. For general ventilating use only. Do not use to exhaust hazard-
ous or explosive materials and vapors.
2. This product is designed for installation in ceilings up to a 12/12
pitch. Duct connector must point up. DO NOT MOUNT THIS
PRODUCT IN A WALL.
3. To avoid motor bearing damage and noisy and/or unbalanced
impellers, keep drywall spray, construction dust, etc. off power
unit.
4. Please read specification label on product for further informa-
tion and requirements.
Installer: Leave this manual with the homeowner.
CLEANING & MAINTENANCE
For quiet and efficient operation, long life, and attractive appear-
ance - lower or remove grille and vacuum interior of unit with the
dusting brush attachment.
The motor is permanently lubricated and never needs oiling. If the
motor bearings are making excessive or unusual noises, replace
the motor with the exact service motor. The impeller should also
be replaced.
OPERATION
The fan, light, and night light can be operated separately. Use a
3-function wall control. Do not use a dimmer switch to operate
the light. See "Connect Wiring" for details.
WARRANTY
BROAN-NUTONE THREE YEAR LIMITED WARRANTY
Broan-NuTone warrants to the original consumer purchaser of its products
that such products will be free from defects in materials or workmanship
for a period of three years from the date of original purchase. THERE ARE
NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE.
During this three-year period, Broan-NuTone will, at its option, repair or
replace, without charge, any product or part which is found to be defective
under normal use and service.
THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP
STARTERS AND TUBES. This warranty does not cover (a) normal
maintenance and service or (b) any products or parts which have been
subject to misuse, negligence, accident, improper maintenance or repair
(other than by Broan-NuTone), faulty installation or installation contrary to
recommended installation instructions.
The duration of an implied warranty is limited to the three-year period as
specified for the express warranty. Some states do not allow limitation
on how long an implied warranty lasts, so the above limitation may not
apply to you.
BROAN-NUTONE'S OBLIGATION TO REPAIR OR REPLACE, AT
BROAN-NUTONE'S OPTION, SHALL BE THE PURCHASER'S SOLE
AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. BROAN-NU-
TONE SHALL NOT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL
OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH
PRODUCT USE OR PERFORMANCE. Some states do not allow the ex-
clusion or limitation of incidental or consequential damages, so the above
limitation may not apply to you.
This warranty gives you specific legal rights, and you may also have other
rights, which vary from state to state. This warranty supersedes all prior
warranties.
To qualify for warranty service, you must (a) notify Broan-NuTone at the
address or telephone number stated below, (b) give the model number and
part identification and (c) describe the nature of any defect in the product or
part. At the time of requesting warranty service, you must present evidence
of the original purchase date.
Broan-NuTone LLC Hartford, Wisconsin
www.broan.com 800-558-1711
MODEL QTR100FLT
Page 

Publicidad

loading

Resumen de contenidos para Broan QTR100FLT

  • Página 1 3. To avoid motor bearing damage and noisy and/or unbalanced warranties. impellers, keep drywall spray, construction dust, etc. off power To qualify for warranty service, you must (a) notify Broan-NuTone at the unit. address or telephone number stated below, (b) give the model number and part identification and (c) describe the nature of any defect in the product or 4.
  • Página 2 MODEL QTR100FLT Page  TYPICAL INSTALLATIONS PLAN THE INSTALLATION COOKING AREA Do not install above or inside this area. NOT FOR USE IN Cooking A COOKING AREA. Equipment Housing mounted to I-joists. Floor Use I-joist spacer block (provided). ROOF CAP 4-IN. ROUND DUCT Housing mounted to joists.
  • Página 3 MODEL QTR100FLT Page  INSTALL HOUSING & DUCT CONNECT WIRING 1. Bend housing tabs. Use a pliers to bend housing TABS out to 90 TABS 2. Mount SPACER housing to (use for mounting to I-Joist) joist. Hold housing in place so that the housing tabs contact the bottom of the joist. The hous- ing mounts with I-JOIST four (4) screws or nails. Screw or...
  • Página 4 MODEL QTR100FLT Page  8. Push grille against ceil- ing. 9. Remove light lens. Carefully insert a small flat-blade screwdriver be- SERVICE NOTE tween grille and To remove Blower Assembly: lens. Pry lens Unplug motor (7). out. Remove thumbscrew (19) from motor plate (9) flange. Find the single TAB on the 10. Install light motor plate (located next to the receptacle).
  • Página 5 Para tener derecho al servicio de la garantía, usted debe (a) notificar a Broan- rociados de yeso, polvos de construcción, etc. NuTone NuTone a la dirección y número de teléfono que aparecen abajo, (b) 4. Léase la etiqueta de especificaciones que tiene el producto para ver proporcionar el número de modelo y la identificación de la pieza y (c) describir...
  • Página 6 MODELO QTR100FLT Página  INSTALACIONES TÍPICAS PLANIFICACIÓN DE LA INSTALACIÓN ÁREA QUE COCINA No instale sobre o dentro de esta área. NO PARA EL USO EN UN Equipo ÁREA QUE COCINA. para cocinar Montaje de la cubierta en viguetas Piso “I”.
  • Página 7 MODELO QTR100FLT Página  CONEXIÓN ELÉCTRICA INSTALE LA CUBIERTA Y EL CONDUCTO 1. Doble las lengüetas de la cubi- erta. Con un alicate, doble las LENGÜE- LENGÜETAS TAS de la cubierta a 90°. 2. Monte la SEPARADOR (se usa cubierta en para el montaje a la vigueta “I”) la vigueta. Sostenga la cubi- erta en su lugar de manera que las lengüetas de...
  • Página 8 MODELO QTR100FLT Página  8. Empuje la rejilla contra el cielo raso. 9. Saque la NOTA DE SERVICIO lente de la Para desmontar el conjunto lámpara. del ventilador: Con cuidado, inserte Desenchufe el motor (7). un destornillador plano pequeño entre Saque el tornillo de mari- la parilla y la lente posa (19) de la brida de la de lámpara. Haga...