Operating Instructions and Parts Manual
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and
others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for
future reference.
Speedaire
Description
Speedaire
®
paint tank is designed for large volume projects using spray guns, paint
rollers and other application equipment. The tank is capable of holding 2.5 gallons of
bulk paint or a 1 gallon can of paint may be placed directly inside the tank.
Basic construction of the unit consists of a heavy deep drawn one piece galvanized
steel tank and die cast aluminum tank lid. The unit is equipped with a pressure
regulator, gauge, safety relief valve, and air line connectors. A convenient carrying
handle allows attachment of the unit to the rung of a ladder or scaffolding to
facilitate elevated painting operations.
Unpacking
After unpacking the unit, inspect carefully
for any damage that may have occurred
during transit. Tighten fittings, bolts, etc.,
before putting unit into service.
Do not operate unit
if damaged during
shipping, handling or use. Damage may
result in bursting and cause injury or
property damage.
General Safety Information
This manual contains information that is
very important to know and understand.
This information is provided for SAFETY
and to PREVENT EQUIPMENT PROBLEMS.
To help recognize this information,
observe the following symbols.
Danger indicates
an imminently
hazardous situation which, if not avoided,
will result in death or serious injury.
Warning indicates a
potentially
hazardous situation which, if not avoided,
could result in death or serious injury.
Caution indicates a
potentially
hazardous situation which, if not avoided,
may result in minor or moderate injury.
Notice
indicates important
information, that if not followed, may
cause damage to equipment.
Specifications
Capacity
1 Gallon can or
2.5 Gallon bulk
Form 5S5662
Paint Tank
®
CALIFORNIA PROPOSITION 65
dust when you cut, sand, drill
or grind materials such as
wood, paint, metal, concrete,
cement, or other masonry. This dust often
contains chemicals known to cause
cancer, birth defects, or other
reproductive harm. Wear protective gear.
contain chemicals known to the State of
California to cause cancer and birth
defects or other reproductive harm. Wash
hands after handling.
SAFETY GUIDELINES
Since the paint tank and other
components used, (air compressor,
material pump, spray guns, filters,
lubricators, hoses, etc.) make up a high
pressure pumping system, the following
safety precautions must be observed at
all times:
1. Read all manuals included
with this product carefully.
Be thoroughly familiar with
the controls and the proper
use of the equipment.
2. Follow all local electrical and safety
codes, as well as in the United States,
the National Electrical Code (NEC) and
the Occupational Safety and Health
Act (OSHA).
Inside Tank
Overall
Dimensions
Dimensions
9.5 inch Dia. x
13.25 inch x 13.25 inch x
9.25 inch H
20 inch
Printed in China
02433
Version 1
07/2014
3. Do not pressurize tank over 50 psi.
You can
4. Do not exceed the pressure rating of
create
any component in the system.
5. Be certain that pressure regulator and
safety valve are clean and in proper
working order before using the paint
tank.
6. Be certain that the air supply line is at
This product or its
zero psi and pressure regulator is
power cord may
turned off before connecting tank to
air supply.
7. Make sure all feed line, brackets and
spray guns are secure before turning
air supply on.
8. Release all pressure within the system
before attempting to service any
component.
9. Protect material lines and air lines
from damage or puncture.
10. Never point a spray gun at yourself or
at any other person. Accidental
discharge may result in serious injury.
11. Check hoses for weak or worn
condition before each use, making
certain that all connections are secure.
12. Always shut off air pressure at source
and bleed off all pressure in paint
tank by gently pulling safety valve
ring before loosening knobs.
Weight
(Empty)
25 lbs.
1ZMG5
Maximum Working
Pressure
50 psi
IN717500AV 7/14
E
N
G
L
I
S
H
E
S
P
A
Ñ
O
L
F
R
A
N
Ç
A
I
S