Publicidad
Enlaces rápidos
Mesh Manager Chair
Fauteuil de direction en mailles
Silla gerencial con malla
Assembly Instructions
Instructions d'assemblage
Instrucciones de ensamble
LZB48085
LA-Z-BOY is a trademark of La-Z-Boy Incorporated and is used under license to LF Products Pte Ltd.
LA-Z-BOY est une marque de commerce de La-Z-Boy Incorporated et est utilisée sous licence à LF Products Pte Ltd.
LA-Z-BOY es una marca de La-Z-Boy Incorporated y es usada con licencia de LF Products Pte Ltd.
Publicidad
Manuales relacionados para LAZBOY LZB48085
Resumen de contenidos para LAZBOY LZB48085
- Página 1 Instructions d’assemblage Instrucciones de ensamble LZB48085 LA-Z-BOY is a trademark of La-Z-Boy Incorporated and is used under license to LF Products Pte Ltd. LA-Z-BOY est une marque de commerce de La-Z-Boy Incorporated et est utilisée sous licence à LF Products Pte Ltd.
-
Página 2: Instrucciones De Ensamblaje
Chair Assembly Instructions Carefully unpack all parts and identify them against the parts list before attempting to assemble. To avoid scratching the components, assemble the chair on a protected surface. Note: The casters sold with this chair are intended for use on carpet and not recommended for use on tile or hard wood floors. Using these casters on tile or wood flooring may cause floor surface damage, so please consider purchasing a chairmat to protect your floor surfaces.We are here to help if you have any questions, comments, or are in need of warranty replacement parts. - Página 3 PARTS/PIÈCES/PARTES Casters X5 Star Base X1 Gas Lift X1 Seat Cushion with Seat Plate X1 Roulettes X5 Base en étoile X1 Vérin pneumatique X1 Coussin de siège avec plaque de siège X1 Ruedas X5 Base en forma de estrella X1 Elevador neumático X1 Cojín del asiento con mecanismo del asiento X1...
- Página 4 Place the star base (B) upside down and insert 5 casters (A) into the holes on the star base (B).Turn the star base (B) over and insert the gas lift (C) through the center hole on top of star base (B). Placez la base en étoile (B) à...
- Página 5 Insert the arms (E1 & E2) to the bottom of the seat frame (with the front of arms facing the front of seat cushion) and attach by using 35 mm screws (G) and allen key (I). *Note: Tighten the screws completely. Insérez les accoudoirs (E1 et E2) dans la partie inférieure du siège (avec le devant des accoudoirs orienté...
- Página 6 Insert back cushion (F) into the rear hole of the seat plate (D) as shown. Then secure with 20 mm screws (H) and allen key (I). *Note: Tighten the screws completely. Insérez le coussin de dossier (F) dans le trou arrière de la plaque du siège (D), comme illustré.
-
Página 7: Function Instruction
Operating Instructions Mode d’emploi Instrucciones de Uso Function Instruction - 1 To Adjust Seat Height: While seated, lean forward and reach under the right side of the chair to find the lever. Lift the lever and raise your body up slightly to allow the chair to rise to the desired height. - Página 8 Function Instruction - 2 To Operate Tilt Lockout: While seated, reach under the left side of the chair to find the lever 1. Push down the lever and lean back to allow the chair to tilt backwards. Pull the lever to the up position to lock the chair angle while the desired position is reached.
- Página 9 Function Instruction - 3 To Adjust Tension On The Tilt: Reach under the front center of the chair, grasp the round knob (R) and turn it counter-clockwise to stiffen the tilt mechanism for a heavier user. Turn the knob (R) clockwise to loosen the tilt mechanism for a lighter user.
- Página 10 Function Instruction - 4 To Adjust Seat Depth: While seated, reach under the left side of the chair to find the lever 2. Lift lever and adjust the seat depth short enough to enable your legs to move freely under the chair.
- Página 11 Function Instruction - 5 To Adjust Arm Height: Press the buttons under the armpads to move them up or down freely then release the buttons once the desired height is reached. Fonction - 5 Pour régler la hauteur des accoudoirs : Appuyez sur les boutons sous les garnitures de bras de se déplacer vers le haut et vers le bas librement puis relâcher les boutons dès que la hauteur désirée soit atteinte.
- Página 12 Function Instruction - 7 To Adjust Back Cushion Height: Grasp the brace of the back cushion while standing behind the chair as shown. Lift the brace slightly. There are 5 notches for various height. Find the height that best suits you. If lifted all the way up, it will release and return to the lowest height.
- Página 13 Function Instruction - 8 To Adjust Lumber support Height: Lumber support height adjust independently for the short and tall by pulling the handle. Fonction - 8 Pour ajuster la hauteur du soutien lombaire : La hauteur du soutien lombaire s'ajuste de façon indépendante en tirant sur la poignée.
- Página 14 Limited Warranty True Innovations seating products are warranted against defects in material and workmanship while owned by the “Original Purchaser”. The term “Original Purchaser” is defined as that party or entity which purchases True Innovations furniture from an authorized True Innovations retailer as shown by the original sales receipt.
- Página 15 Garantie limitée Les fauteuils de True Innovations sont garantis contre tout défaut de matériaux et de fabrication à « l’acheteur initial ». Le terme « acheteur initial » se définit comme la personne ou entité qui achète le meuble True Innovations d’un détaillant True Innovations autorisé, tel qu’attesté...
- Página 16 Garantía Limitada Los productos de True Innovations seating están garantizados contra defectos de material y mano de obra mientras está en posesión de su “Comprador Original”. El término “Comprador Original” se define como el individuo o entidad que compra el mueble de True Innovations de un distribuidor autorizado así...