Important Safety Instructions - McCulloch MCP1510 Manual Del Usuario

Sierra telescopia electrica
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

2 - SAFETY PRECAUTIONS

2-3. IMPORTANT SAFETY INSTRUCTIONS

WARNING
When using an electric chain saw, basic safety precautions
should always be followed to reduce the risk of fire, electric
shock, and injury to persons, including the following:
READ ALL INSTRUCTIONS
1.
Double insulated - No Serviceable Parts Inside.
2.
To reduce the risk of electric shock, this equipment
has a polarized plug (one blade is wider then the
other). This plug will fit in a polarized outlet only one
way. If the plug does not fit fully in the outlet, reverse
the plug. If it still does not fit, contact a qualified elec-
trician to install the proper outlet. Do not change the
plug in any way.
3.
With a basic understanding of kickback, you can
reduce or eliminate the element of surprise. Sudden
surprise contributes to accidents.
4.
KEEP THE WORK AREA CLEAN: Cluttered areas
invite injuries. Do not start cutting until you have a
clear work area, secure footing, and a planned retreat
path from the falling tree.
5.
GUARD AGAINST ELECTRIC SHOCK: Prevent body
contact with grounded surfaces (i.e., metal pipes, wire
fences).
6.
CONSIDER THE WORK AREA ENVIRONMENT: Use
extreme caution when cutting small sized brush and
sapling, as slender material may catch the saw chain
and be whipped toward you or pull you off balance. Do
not operate a chain saw in a tree unless you are
specifically trained to do so. When cutting a limb that
is under tension, be alert for spring back so that you
will not be struck when the tension in the wood fibers
is released. Do not expose the chain saw to rain. Do
not use the chain saw in damp or wet locations. Do not
use the chain saw in the presence of flammable liq-
uids or gases.
7.
KEEP CHILDREN AND BYSTANDERS AWAY: Do not
let visitors contact the chain saw or extension cord. All
visitors should be kept away from the work area.
8.
STORING YOUR CHAIN SAW: When not in use, chain
saws should be stored out of the reach of children, in
a dry, high or locked-up place. When storing saw, use
a scabbard or carrying case.
9.
DO NOT FORCE THE CHAIN SAW: The chain saw
will do a better and safer job when used at the rate for
which it was intended.
10. USE THE RIGHT TOOL: Cut wood only. Do not use
the chain saw for purposes for which it was not intend-
ed. For example, do not use the chain saw for cutting
plastic, masonry, or non-building materials.
11. DRESS PROPERLY: Do not wear loose clothing or
jewelry, as they can get caught in moving parts. Non-
skid footwear is recommended when working out-
doors. Wear protective hair covering to contain long
hair.
12. USE SAFETY GEAR: UsE safetY glasseS, safety foo-
twear, safety chaps, snug fitting clothing, protective
gloves, and protective hearing and head gear.
13. STAY ALERT: Watch what you are doing. Use com-
mon sense. Do not operate the chain saw when you
are tired. Keep all parts of your body away from the
saw chain when the motor is operating. Before you
start the saw, make sure the saw chain is not contact-
ing anything.
14. MAINTAIN YOUR CHAIN SAW: Inspect the chain saw
cords periodically and, if damaged, have them
repaired by an authorized service facility. Keep the
cord clear of the chain and operator at all times. Never
carry the saw by the cord or pull it to disconnect from
receptacle. Keep the cord from oil and sharp edges.
Inspect the extension cords periodically and replace if
damaged. Keep tools sharp and clean for better and
safer performance. Follow instructions for lubricating
and changing accessories. Keep handles dry, clean
and free from oil and grease.
15. DISCONNECT THE CHAIN SAW: Disconnect the
chain saw when not in use, before servicing, and
when changing accessories and attachments such as
saw chain and guard.
16. OUTDOOR EXTENSION CORDS: Use only exten-
sion cords intended for use outdoor use and so mark-
ed accordingly.
17. CHECK DAMAGED PARTS: Before further use of the
chain saw, a guard or other part that is damaged
should be carefully checked to determine that it will
operate properly and perform its intended function.
Check for alignment of moving parts, binding of mov-
ing parts, breakage of parts, mounting, and any other
conditions that may affect its operation. A guard or
other part that is damaged should be properly
repaired or replaced by an authorized service center,
unless otherwise indicated in this instruction manual.
Have defective switches replaced by authorized serv-
ice centre. Do not use chain saw if switch does not
turn it on and off. Do not operate a chain saw that is
damaged, improperly adjusted, or is not completely
and securely assembled. Be sure that the saw chain
stops moving when the trigger is released.
18. CARRYING THE SAW: Carry the saw by the front
handle with the saw stopped. Keep your finger off the
switch, and make sure that the guide bar and saw
chain are to the rear.
6
2 - SAFETY PRECAUTIONS
19. GUARD AGAINST KICKBACK:
WARNING
Kickback may occur when the nose or tip of the guide bar
touches an object, or when the wood closes in and pinch-
es the saw chain in the cut. Tip contact in some cases may
cause a lightning-fast reverse action, kicking the guide bar
rapidly back towards the operator. Pinching the saw chain
along the top of the guide bar may push the guide bar rap-
idly back towards the operator. Either of these reactions
may cause you to lose control of the saw, which could
result in serious injury to the user. The following precau-
tions should be followed to minimize kickback.
A. GRIP SAW FIRMLY: Hold the chain saw firmly with
both hands when the motor is running. Keep a
good firm grip on the saw with both hands, the
right hand on the rear handle, and the left hand on
the front handle.
B. Do not over reach.
C. Keep proper footing and balance at all times.
D. Do not let the nose of the guide bar contact a log,
branch, ground or other obstruction.
E. Do not cut above shoulder height.
F. Use devices, such as low-kickback chain, guide
bar nose guards, chain brakes and special guide
bars, which reduce the risks associated with kick-
back.
G. Use only replacement bars and chains specified
by the manufacturer or the equivalent.
H. There are no other replacement components for
achieving kickback protection in accordance with
CSA Z62.3.
20. POWER SUPPLY: Connect the chain saw to correct
voltage; be sure that the voltage supplied is the same
as that specified on the nameplate of the tool.
21. DO NOT operate a chain saw that is damaged,
improperly adjusted, or not completely and securely
assembled. Be sure that the saw chain stops moving
when the trigger is released.
22. DO NOT attempt operations beyond your capacity or
experience.
23. DO NOT operate a chain saw with one hand! Serious
injury to the operator, helpers, or bystanders may
result from one-handed operation. A chain saw is
intended for two-handed use.
24. TO REDUCE potential for electric shock, do not oper-
ate the saw on wet or slippery surfaces, or during
snow storms, rain storms, and other adverse weather
conditions.
25. DO NOT allow dirt, debris or sawdust to build up on
the motor or outside air vents.
26. Follow the manufacturer's sharpening and mainte-
nance instructions for the saw chain.
27. Cut at high motor speeds.
28. Operation of a chain saw should be restricted to
mature, properly instructed individuals.
29. Your chain saw is intended for occasional homeowner
use. It is not made for continuous heavy duty use.
30. DO NOT FORCE a small saw to do a job requiring a
heavier duty unit.
31. EXAMINE THE ELECTRICAL SWITCHES. Do not
use the chain saw if the switches do not properly turn
on and off. Do not attempt to make any repairs to the
electric switches. Take your saw to a McCulloch
Authorized Service Center.
32. MAINTAIN EXTENSION CORDS. Inspect the exten-
sion cords periodically and replace if damaged. Only
use power cords that are suitably marked for outdoor
use.
33. DO NOT OPERATE YOUR CHAIN SAW near or
around flammable liquids or gases, whether in or out
of doors. An explosion and/or fire may result.
34. This electric powered saw is classified by CSA as a
Class 2C saw. It is intended for infrequent use by
homeowner's, cottagers and campers, and for such
general applications such as clearing, pruning, cutting
firewood, etc. It is not intended for prolonged use. If
the intended use involves prolonged periods of oper-
ation, this may cause circulatory problems in the
user's hands due to vibration. It may be appropriate to
use a saw having an anti-vibration feature.
35. NEVER REMOVE, modify or make inoperative any
safety device furnished with your unit.
36. Safety clothing required by your safety organizations,
government regulations, or your employer should be
used; otherwise, snug fitting clothing, safety footwear,
safety chaps and hand and ear protection should be worn.
37. When felling, keep at least two (2) tree lengths betw-
een yourself and your fellow workers.
38. All chain saw service, other than the items listed in the
user manual safety and maintenance instructions,
should be performed by competent chain saw person-
nel. Do not attempt to repair it yourself; there are no
user serviceable parts inside.
NOTE: Low-kickback saw chain is chain that has met the
kickback performance requirements of ANSI B175.1-1991
and is in accordance with CSA Z62.3. Do not use other
replacement chain unless it has met these requirements for
your specific model.
39.
DO NOT USE ANY OTHER CUTTING ATTACH-
MENT OR ACCESSORIES. Use only McCulloch
replacement parts and accessories, which are
designed specifically to enhance the performance and
maximize the safe operation of our products. Failure to
do so may cause poor performance and possible
injury. Use only the chain and bar supplied with this
product. Do not use any other cutting attachment. Use
of such attachments will void your factory warranty
and could result in serious bodily injury.
7

Publicidad

Tabla de contenido
loading

Tabla de contenido