Important Safety Rules; Safety Symbols; Electrical Safety Guidelines - Olympia PS-35 CC Instrucciones De Uso

Important safety rules

Please read the instructions thoroughly before using the device to make sure that you
are able to use all of its functions.
Keep children and pets away from the device. The device may only be used by adults.
The device can only be used by one person at a time. Do not conduct any other
activities on the device (e.g. cleaning) when it is in use.
Have any necessary repairs performed by qualified specialist personnel.
Protect the device against direct sunshine, extreme heat and moisture.
The following warning sign is attached to the bottom of the device.
Danger of electric shocks!
Gefahr eines elektrischen Schlages!
Do not open the device.
Gerät nicht öffnen!
Device contains no user-serviceable parts.
Keinerlei vom Benutzer austauschbare Teile inseitig.
Device should only be opened by trained
Gerät nur von geschultem Fachpersonal öffnen lassen.
specialist personnel.
Failure to observe this warning sign can lead to injuries.

Safety symbols

Do not reach into the infeed slot.
Keep ties, scarves, loose
clothing and long necklaces or
bracelets out of the area around
the infeed slot.
Caution: failure to observe these safety symbols can lead to serious injuries.
If an object (sleeve, tie, etc.) is inadvertently fed into the infeed slot, pull out the
mains plug immediately.

Electrical safety guidelines

Pull out the mains plug before emptying the paper collecting basket, cleaning the
-
device or if the device is not going to be used for a long time.
If the mains cable, mains plug or the device itself is damaged do not operate the
-
device any longer (danger of injuries).
Do not overload the recommended capacity of the mains socket.
-
Do not make any alterations to the mains cable as it has been designed for the
-
specified mains voltage.
Achtung
Caution
Do not insert paper clips or
staples into the infeed slot.
Keep long hair out of the area
around the infeed slot.
Operating elements
The sliding switch (OFF / ON/AUTO / REVERSE) on the device has the following
functions.
OFF position: the device is switched off.
ON/AUTO position: the device is ready for operation.
REV position: the cutting unit runs in reverse. To hold the rest of the paper back, you
can push the sliding switch in the REV position. The cutting unit runs backwards and
pushes the paper back.
The device also has a microswitch:
shredding starts as soon as paper in inserted in the infeed slot.
Materials suitable for destruction
Only use the PS-35CC paper shredder to shred paper. The paper must be dry and
must correspond to the specifications listed in the technical data. Shredding other
materials can lead to injuries (for example, if solid material splinters) or damage to the
device (destruction of the cutting unit, etc.).
Do not shred endless paper documents with this device. Remove all paper clips and
staples before feeding paper into the device.
Take the device carefully out of the packaging and place it on the paper collection
-
basket. The bulge in the paper collection basket must point to the front. The device
can only be operated when it has been put properly in place (contact switch).
Plug the mains cable into the socket. Please observe the energy supply
-
specifications on the back of the device in your safety measures.
The socket and the mains connection of the device must be freely accessible for
-
safety reasons so that the power supply can be disconnected in emergencies.
Switch the device on with the sliding switch (ON/AUTO position).
-
Feed the paper to the cutting unit through the infeed slot.
-
The device runs forwards and draws the paper in.
-
The device switches off automatically after the shredding cycle. The motor carries on
-
running for another 2-3 seconds to remove the remaining paper from the cutting unit.
Caution: the sheet capacity given in the technical data may not be exceeded as
otherwise a paper jam will occur. Remember that the thickness of the paper increases
when it is folded and the recommended sheet capacity may be exceeded in this way.
Reduce the quantity of paper fed if it is coarse fibre paper.
it is recommended not to fill the paper collection basket up to the cutting unit. This
prevents cut material becoming jammed in the cutting unit.
Empty the paper collection basket at regular intervals.
Starting up
Paper supply