Aastra 5370 Manual De Instrucciones página 6

Forwarding Calls
1. Press , then
M F
ENU
2. Select the type of forwarding
3. Select the destination (user
4. Enter the call number and validate.
Reset call forwarding with
> >
F S
EATURES ELECT
Deflecting a Call During the Ringing Phase
1. Press during the ringing phase.
D
EFLECT
2. Enter the call number and press
Transferring During a Call
1. Press the Call key or
call number and wait until the called party an-
swers.
2
2. Press /
C T
ONNECT RANSFER
ferred. If no-one answers, cancel with
2 3
/ and take back the first call.
R
CALL ECOVER
Brokering
Switches between two callers without interrupt-
ing the calls. You are making/taking a call:
1. Press
E
NQUIRY CALL
wait until the call is answered.
2. Press to switch back and forth be-
B
ROKERING
tween the callers.
Conference Call
Connects several callers for a conference call. You
are making/taking a call:
1. Press
E
NQUIRY CALL
wait until the call is answered.
2. Press .
C
ONFERENCE
3. Add other callers using
Leaving a conference call: Press the End key.
Callback
The person is busy or does not answer:
Resetting activated features
You can deactivate again all the call forwardings
and other temporarily active functions: Press
>
M A F
ENU CTIVATED EATURES
the function you want.
D
ELETE
Installation and Connection
You can set up the phone either at a 40° or a 25°
angle:
1. Insert the footstand as indicated on the instal-
lation diagram until it snaps into place.
2. Plug in the handset and phone cords and feed
them through the cable holders.
>
S
ORWARDING ELECT
1
.
2
/subscriber
then
M A
ENU CTIVATED
/ .
R D
ESET ELETE
2
.
OK
, enter the
E
NQUIRY CALL
3
; the call is trans-
E
, enter the call number and
, enter the call number and
1
again.
E
NQUIRY CALL
C
ALLBACK
> and
S
ELECT
3. Insert the Aastra M530/M535
module as indicated in the drawing, snap it
.
into place and plug in the connection cable
and power cord if required.
3
).
Notes
• Some function commands of the vocal
announcements
minal.
• Always disconnect the phone from the mains
first before you connect/disconnect an
Aastra M530/M535
• Always install the footstand before you plug in
the cables.
• Always remove the cables before you detach
the footstand.
Connections
ND
or
.
Document Designation
• Document number: eud-0988 / 1.2
• Valid as of: Aastra 5000 R5.1 / Aastra 400 series
/
R
ESET
as of R1.0 / Aastra IntelliGate® series as of I7.7
• Copyright © 09.2010 Aastra Technologies Limited
Declaration of Conformity, User's Guide and oth-
er documents can be found at
www.aastra.com/docfinder
www.aastra.com
2
3
are not to apply on this ter-
2
expansion key module.
Connecting to the IP network
(Aastra 5370ip only)
Connecting the PC
(only Aastra 5370ip)
Connecting the power supply
(Aastra 5370ip only)
Telephone connection cable
(Aastra 5370 only)
Connecting the handset
Connecting the headset
Connection Aastra M530/M535
pansion key module or power supply
Connecting the Aastra M530/M535
expansion key module
Connection power supply or
2
Aastra M535 expansion key module
2
or
3
.
expansion key
2
ex-
2