Descargar Imprimir esta página
Leviton 47612 Instrucciones De Instalación
Leviton 47612 Instrucciones De Instalación

Leviton 47612 Instrucciones De Instalación

Placa universal de seguridad

Publicidad

Enlaces rápidos

Security Plate
Cat. No. 47612
DI-000-47612-20A
InStallatIon InStrUctIonS
Plaque de
sécurité universelle
N
de cat. 47612
o
DIrEctIVES
Placa Universal
de Seguridad
No de Cat. 47612
InStrUccIonES DE InStalacIon
lIMItED 2 YEar WarrantY anD EXclUSIonS
Leviton warrants to the original consumer purchaser and not for the
benefit of anyone else that this product at the time of its sale by Leviton
is free of defects in materials and workmanship under normal and proper
use for two years from the purchase date. Leviton's only obligation is to
correct such defects by repair or replacement, at its option, if within such
two year period the product is returned prepaid, with proof of purchase
date, and a description of the problem to leviton Manufacturing co.,
Inc., att: Quality assurance Department, 59-25 little neck Parkway,
little neck, new York 11362-2591. This warranty excludes and there is
disclaimed liability for labor for removal of this product or reinstallation.
This warranty is void if this product is installed improperly or in an
improper environment, overloaded, misused, opened, abused, or altered
in any manner, or is not used under normal operating conditions or not
in accordance with any labels or instructions. there are no other or
implied warranties of any kind, including merchantability and fitness
for a particular purpose, but if any implied warranty is required by the
applicable jurisdiction, the duration of any such implied warranty, including
merchantability and fitness for a particular purpose, is limited to two years.
leviton is not liable for incidental, indirect, special, or consequential
damages, including without limitation, damage to, or loss of use of,
any equipment, lost sales or profits or delay or failure to perform this
warranty obligation. The remedies provided herein are the exclusive
remedies under this warranty, whether based on contract, tort or otherwise.
For technical assistance call:
1-800-824-3005 (U.S.a. only)
www.leviton.com
Universal
WarnInG
Hazard of electric shock! Not intended for installation on powered wire or circuits. Extreme caution should be exercised to avoid physical contact with bare
conductors or terminals, as ringing voltage could be in excess of 100 volts AC. Never attempt repair, installation, or modification of low voltage equipment or wiring
systems if you wear an electronic heart regulation device. If you are unfamiliar with low voltage wiring, consult a qualified technician. For more information, refer to
specific product instruction sheets.
IMPortant InStrUctIonS
1.
Read and understand all instructions. Follow all warnings and instructions marked on the product.
2.
Do not use this product near water—e.g., near a tub, wash basin, kitchen sink or laundry tub, in a wet basement, or near a swimming pool.
3.
Never push objects of any kind into this product through openings, as they may touch dangerous voltages.
4.
SAVE THESE INSTRUCTIONS.
SaFEtY InForMatIon
Never install communications wiring or components during a lightning storm.
1.
2.
Never install communications components in wet locations unless the components are designed specifically for use in wet locations.
3.
Never touch uninsulated wires or terminals unless the wiring has been disconnected at the network interface.
4.
Use caution when installing or modifying communications wiring or components.
1.
Align the mounting pins with the grid holes on the back of the enclosure. The bracket may be mounted horizontally or vertically. With the mounting pin plungers
in the "out" position, press the unit into the grid in the desired location, secure by pushing the plungers in (Fig. 1).
2.
Connect wires to circuit board to be mounted (Do not energize).
Attach adhesive mounting clips to circuit board (Fig. 2).
3.
4.
Remove paper backing from adhesive mounting clips. notE: For best adhesion of mounting clips proceed as follows:
• Clean Universal Security Plate surface of dust, debris, fingerprints, etc. before mounting adhesive backed mounting clips.
• Do not touch the adhesive when the paper liner is removed.
• For best adhesion, install between 70° and 100°F (21° and 38°C).
• Do not mount excessively heavy circuit boards of any kind onto the Universal Security Plate.
5.
Press clips firmly onto Universal Security Plate in desired location (Fig. 3).
6.
Energize and test circuit board.
Fig. 1
Security Plate
Plaque de sécuritié
Placa de seguridad
DI-000-47612-20A
Fig. 2
Structured Media center
Centre média structuré
Centro de Media Estructurada
Pc Board (not supplied)
Carte de circuits inprimés (non comprise)
Tablero PC (no suministrado)
English
InStallatIon
Fig. 3
Mounting clips (4)
Agrafes de fixation (4)
Clips de montaje (4)
Structured Media center
Centre média structuré
Centro de Media Estructurada
Security Plate
Plaque de sécuritié
Placa de seguridad

Publicidad

loading

Resumen de contenidos para Leviton 47612

  • Página 1 Leviton warrants to the original consumer purchaser and not for the Centre média structuré Centre média structuré benefit of anyone else that this product at the time of its sale by Leviton Centro de Media Estructurada Centro de Media Estructurada is free of defects in materials and workmanship under normal and proper use for two years from the purchase date.
  • Página 2 2 ans, à la Manufacture leviton du canada bien connaître ce type de câblage, on doit faire appel à un technicien qualifié. Pour plus de renseignements, se reporter aux directives accompagnant limitée, au soin du service de l’assurance Qualité, 165 boul.