Tabla De Contenido - Horizon Global 76199 Instrucciones De Instalación

Always wear SAFETY GLASSES
when installing hitch
Exhaust
Hanger
Bracket
Factory M8
Flange Nut
Figure 1
Figure 3
2.0"
1. Remove fascia panel - Using T25 torxbit socket, remove (6) screws from rear bottom fascia.
2. Remove underbody panels - Using T25, T27, 10 mm socket, remove (6) screws and (1) flange nut from underbody panel per side.
3. Remove bumper fascia - (a) Using plastic trim tools, loosen the lower part of wheel well trim by unclipping the tabs from fascia and gently pulling it outward both sides. (b) Using
T25 torxbit socket, remove (1) screw in the upper area behind wheel well trim both sides. (c) Open lift gate. Using T30 torxbit socket, remove (2) screws near trunk weather seal. (d)
Using plastic trim tools, remove the fascia starting at the outer edge near wheel wells, and gently pulling the fascia. (e) Unplug the wiring on passenger side if present.
4. Remove bumper beam - Using 13 mm socket, remove (3) factory M8 bolts from bumper plate per side. Gently remove the bumper beam and return it to owner.
5. Install hitch - (a) Raise the hitch into position. Slide the hitch brackets into end panel opening and align the holes in hitch with end panel studs, see Figure 1. (b) Using pull wire ⑤,
feed the carriage bolt ① and spacer ② through end panel opening. Pull the wires out through bracket holes and frame rails holes. Remove pull wires and loosely install the conical
washer ③ and ½''nut ④ to the bolt. (c) Install flat washer ⑥, lock washer ⑦, and M8 nut ⑧ to top two end panel studs. Reuse factory M8 flange nut and install it to the bottom
end panel stud with exhaust hanger bracket, see Figure 1.
6. Tighten all 1/2'' fasteners with torque wrench to 75 Lb.-Ft. (102 N*M) and all M8 fasteners to 27 Lb.-Ft. (37 N*M) .
7. Trim bumper fascia and fascia panel - Using marker and utility knife, cut a notch on the bottom fascia, see Figure 2, and cut fascia panel into two pieces, see Figure 3.
8. Reinstall all fasteners, wirings, bumper fascia, and panels removed in Step 1-3.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent entry of water and exhaust fumes. A hitch or ball which has been damaged
should be removed and replaced. Observe safety precautions when working beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for
connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684.
©2018 Horizon Global™ Corp - Printed in Mexico
Installation Instructions
PART NUMBERS: 76199, 84199, CQT76199
⑤
Fasteners
typical
both sides
End Panel
①
②
⑥
⑦
⑧
2.0"
①
②
③
Conical washer
teeth side ④
against hitch
⑤
⑥
⑦
③
⑧
④
C L
2.25''
Figure 2
Proper torque is needed to keep the hitch
secure to the vehicle when towing.
Sheet 3 of 30 76199NP
Fastener Kit: 76199F
Qty. (4) Carriage bolt
1/2''-13 x 1.75, GR5
Qty. (4) Spacer .250 x 1.0 x 2.0
Part #: 5121
Qty. (4) Conical washer 1/2''
Part #: 01292008
Qty. (4) Hex nut 1/2''-13, GR5
Qty. (4) Pull wire 1/2''
Part #: 5482
Qty. (4) Flat Washer 5/16''
Qty. (4) Lock Washer 5/16''
Qty. (4) Nut M8 x 1.25, CL10
3.5"
05-01-18 Rev. A