Westin AUTOMOTIVE PRODUCTS EQUIPO DE MONTAJE Instrucciones

AUTOMOTIVE PRODUCTS, INC.
MOUNT KIT
EQUIPO DE MONTAJE
JEU DE MONTAGE
27-1755
STEP BOARD
27-0020
27-0025
27-6140
27-6145
27-6540
ITEM QTY
CONTENTS -
1 2 STEP BOARD (PURCHASED SEPARATELY)
2 6 MOUNT BRACKET
3 12 M8-1.25 X 30MM HEX HEAD BOLT
4 6 M8-1.25 HEX NUT
5 2 M8-1.25 EXTRUDED U-NUT
6 12 5/16-18 X .75 SQUARE HEAD BOLT
7 30 5/16" FLAT WASHER
8 12 5/16" LOCK WASHER
9 12 5/16" HEX NUT
1 2 ESTRIBOS (SE COMPRAN POR SEPARADO)
2 8 SOPORTES DE MONTAJE
3 12 PERNOS CON CABEZA HEXAGONAL M8-1.25 X 30MM
4 6 TUERCAS HEXAGONALES DE M8-1.25
5 2 TUERCA A PRESIÓN EN "U" M8-1.25
6 12 PERNOS CON CUADRADA DE 5/16-18 X .75
7 30 ARANDELAS PLANAS DE 5/16"
8 12 ARANDELAS DE PRESIÓN DE 5/16"
9 12 TUERCA A PRESIÓN 5/16"
1 2 MARCHEPIED (VENDU SÉPARÉMENT)
2 8 SUPPORTS DE MONTAGE
3 12 BOULONS A TETE HEXAGONALE M8-1.25 X 30MM
4 6 ÉCROUS HEXAGONAUX M8-1.25
6 2 ECROU EN U EXTRUDE M8-1.25
7 12 BOULONS A TETE CARREE 5/16-18 X .75PO
8 30 RONDELLE PLATE 5/16 PO
9 12 RONDELLES A FREIN 5/16 PO
10 12 ECROU FREINE 5/16 PO
STEP 1. Remove contents from box and check for damage. Verify all parts are present. Read instructions completely before
beginning.
Attach mounting brackets as shown.
STEP 2.
STEP 3. Insert square head bolts as shown (3 per slot, 6 per Step Board/Running Board).
NOTE: For lighted Step Board/Running Board, run wiring harness prior to attaching step board to brackets (refer to Step
6) Run longer wire harness on passenger side. .
STEP 4. For Aluminum Running boards, if desired, slide closure strip as shown. Set lights (if included) in appropriate location.
Attach to running board as shown.
STEP 5.
Attach Step board / Running board to brackets as shown. Make sure step board and brackets are properly aligned and tighten fasteners.
Recommended torque values are 10 FT.LBS. for 5/16" square head fasteners and 23 FT.LBS. for 8mm fasteners.
NOTE: For lighted version of Step board, remove plastic cover from each end of under side of Step board. Proceed to
Steps 6-7.
WARNING: INSTALLING LIGHT HARNESS REQUIRES SPLICING INTO VEHICLES ELECTRICAL SYSTEM. WESTIN
RECOMMENDS USING A PROFESSIONAL FOR THIS INSTALLATION. NOTE: AVOID AREAS OF
INSTRUCTIONS-INSTRUCCIONES-CONSIGNES
APPLICATION: 2007-UP CHEVY SILVERADO/ GMC SIERRA 1500 SERIES CREW CAB
APLICACIÓN: CHEVY SILVERADO MC SIERRA 1500, 2007 Y SUPERIOR CREW CAB
APPLICATION: CHEVY SILVERADO/GMC SIERRA 1500, 2007 ET PLUS CREW CAB
1
CONTENIDO - CONTENU
See Figure 7 and 8.
See Figure 1.
/G
Drill hole through plastic strip and run wires as shown.
WO: 202935
2
TOOLS- HERRAMIENTA -OUTILS
13MM SOCKET
13MM WRENCH
1/2" SOCKET
RATCHET
TORQUE WRENCH
DADO DE 13MM
LLAVE DE TUERCAS DE 13MM
DADO DE 1/2"
MANERAL
LLAVE DE TORQUE
DOUILLE 13MM
CLÉ 13MM
DOUILLE 1/2 PO
CLIQUET
ClÉ DE COUPLE
See Figures 2 and 3.
See Figure 5.
75-0768 REVISION A 2/9/07
See Figure 4.