Westin 27-1885 Instrucciones

AUTOMOTIVE PRODUCTS, INC.
MOUNT KIT
EQUIPO DE MONTAJE
JEU DE MONTAGE
27-1885
SURE-GRIP
MOLDED
BOARDS
BOARDS
27-6140
27-6145
27-6540
ITEM QTY
CONTENTS -
1,2 2 STEP BOARD, PASSENGER (1) AND DRIVER (2) (SOLD SEPARATELY)
3 2 FRONT BRACKET
4 2 CENTER BRACKET
5 2 REAR BRACKET
6 10 5/16-18 X 1.00" HEX HEAD BOLT
7 12 5/16-18 X .75" SQUARE HEAD BOLT
8 28 5/16" FLAT WASHER
9 10 5/16" LOCK WASHER
10 12 5/16-18 NYLOCK NUT
11 4 EXTRUDED U-NUT
12 6 5/16-18 HEX NUT
13 2 ½" HEX NUT
14 2 ½"BOLT PLATE
15 2 ½"WASHERS LOCK
16 2 ½" FLAT WASHERS
1,2 2 ESTRIBOS, ACOMPAÑANTE (1) CONDUCTOR (2) (SE COMPRA SEPARADO)
3 2 SOPORTE DELANTERAS
4 2 SOPORTE CENTERAL
5 2 SOPORTE TRASERO
6 12 PERNOS CON CABEZA HEXAGONAL DE 5/16-18 X 1,00"
7 12 PERNOS CON CABEZA CUADRADA DE 5/16-18 X ,75"
8 30 ARANDELAS PLANAS DE 5/16"
9 10 ARANDELAS DE PRESIÓN DE 5/16"
10 12 TUERCA PRESIÓN DE 5/16"
11 4 TUERCA A PRESIÓN EN "U"
12 6 TUERCAS HEXAGONALES DE 5/16-18
13 2 TUERCA DE ½"
14 2 PERNO DE LA PLACA ½"
15 2 ARANDELA DE PRESION ½"
16 2 ARANDELA DE PLANAS DE 1/2"
1,2 2 MARCHE-PIEDS, PASSAGER (1) ET CONDUCTEUR (2) (ACHETE SEPAREMENT)
3 2 SUPPORTS AVANT
4 2 SUPPORTS CENTRAL
5 2 SUPPORTS ARRIELE
6 12 BOULONS A TETE HEXAGONALE 5/16-18 X 1,00 PO
7 12 BOULON A TETE CARREE 5/16 PO
8 30 RONDELLES PLATES 5/16 PO
9 10 RONDELLES A FREIN 5/16 PO
10 12 ECROU A FREIN 5/16 PO
11 4 ECROU EN U EXTRUDE
12 6 ÉCROUS HEXAGONAUX 5/16-18
13 2 ECROU ½"
14 2 PLAQUE BOULON ½"
15 2 RONDELLES A FRIEN ½"
16 2 RONDELLES PLATES 1/2"
STEP 1. Remove contents from box and check for damage. Verify all parts are present. Read instructions completely before beginning. It is strongly
recommended to install the Sure Grip Gap Strip for these vehicle applications.
STEP 2. Locate mounting locations as shown. SEE FIGURE 1.
STEP 3. Install u-nuts as shown. SEE FIGURES 2 AND 3.
STEP 4. Attach mounting brackets as shown. Hand tighten. SEE FIGURES 4 AND 5.
STEP 5. ATTACH THE REAR MOUNTING BRACKET BY LOCATING THE LARGE CIRCULAR HOLE IN THE ROCKER PANEL INSERT (1) 1/2" BOLT PLATE INTO THE
HOLE AND ATTACH THE REAR BRACKET USING (1) ½ FLAT WASHER, (1) ½ LOCK WASHER, AND (1) ½ HEX NUT, ONCE ATTACHED DRILL A 5/16
HOLE THROUGH THE PINCH WELD AND ATTACH USING 5/16 HARDWARE.
STEP 6. Insert square head bolts as shown. (3 per slot, 6 per board). SEE FIGURES 8 AND 9.
NOTE: For lighted boards, run wiring harness prior to attaching board to brackets (refer to Step 8). SEE FIGURES 8,9, AND 10. Run longer wire harness
on passenger side.
STEP 7. For Sure-Grip Running Boards, slide closure strip as shown. Set lights (if purchased) in appropriate location. Attach to Sure-Grip Running Board as
shown. SEE FIGURE 7. Drill hole through plastic strip and run wires as shown. SEE FIGURE 10.
STEP 8. Attach board to brackets as shown. Make sure board and brackets are properly aligned and tighten fasteners. Recommended torque values are 10
FT.LBS. for 5/16" square head fasteners, 15 FT. LBS for 5/16" fasteners , 26 FT.LBS. for 3/8" fasteners and 50 ft lbs for 1/2" fasteners. SEE FIGURE 11.
NOTE: For lighted version of Step board, remove plastic cover from each end of under side of Step board. Proceed to Steps 8 and 9.
WARNING: INSTALLING LIGHT HARNESS REQUIRES SPLICING INTO VEHICLES ELECTRICAL SYSTEM. WESTIN RECOMMENDS USING A PROFESSIONAL FOR THIS
INSTALLATION. NOTE: AVOID AREAS OF EXCESSIVE HEAT, VIBRATION, PINCH OR ROTATION WHEN SECURING HARNESS TO VEHICLE. CAUTION:
INSTRUCTIONS-INSTRUCCIONES-CONSIGNES
APPLICATION: 2009-12 FORD F-150 SUPER CREW
APLICACIÓN: FORD F-150 CABINA
APPLICATION: 2009-12 FORD F-150 CABINE SUPER CREW
SURE-GRIP
OPTIONAL
LIGHT KIT
27-6000
27-0020
27-0025
1
CONTENIDO - CONTENU
SUPER CREW 2009-12
4 4
3
4
W11-0999 75-0897 REVISION C
5
TOOLS- HERRAMIENTA -OUTILS
1/2" SOCKET
½" WRENCH
3/4" SOCKET
RATCHET
TORQUE WRENCH
DADO DE 1/2"
LLAVE DE TUERCAS DE 1/2"
DADO DE 3/4"
MANERAL
LLAVE DE TORQUE
DOUILLE 1/2 PO
CLE ½ PO
DOUILLE 3/4"
CLIQUET
CLE DE COUPLE
12/19/11