Troubleshooting - Brill 270 RT Tipp Manual Del Usuario

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 62
Maintenance
Maintenance includes all work
carried out to keep the unit in
GB
proper working order.
Never use spare parts and
accessories that have not been
authorised by the manufacturer.
Observe the notes on installation
when installing a new line reel.
Installing a New Cutting Line
8.1. Installing a New Line Reel
(Figure A / A1)
Take care not to injury yourself
on the devices used to cut the line.
A new line reel must be installed
once all the line has been used
up.
Never use metal cutting ele-
ments, replacements parts or
accessories that have not been
authorised by the manufacturer.
Please only use the replacement
line reel recommended by the
manufacturer. Replacement line
reels are available from your
specialist dealer.
Replacement Line (original
Brill replacement part
Article No. 75062)
Replacement Line (original
Brill replacement part
Article No. 75060)
A) Unplug the mains plug!
B) On the underside of the unit
you will find the cutting head
(10) with the line reel (12)
and line feed button (15).

9. Troubleshooting

General
Faults usually occur if the unit
has not been handled, cared for
22
Hold the ribbed part of the cut-
ting head tight with one hand.
Use the other hand to press in
the tab located inside the cover.
Turn the cover anticlockwise to
loosen in (Figure K / L).
C) Remove the empty line reel.
Note: If the line reel is not
released automatically, turn it
anticlockwise.
D) Insert the new line reel ensur-
ing that the cutting line is
fed out through one of the
openings in the cutting head
(Figure O).
E) Press down the line reel
against the force of the
spring and secure the reel in
this position by pressing it
briefly to the left or right.
F) Fit the cover and screw it
clockwise until the tab clips
back into place.
Hold the Lawn Trimmer in the
normal working position before
you switch it on again.
8.1.1. Line drawn into the reel
(Figure M / N / O)
The line cannot be lengthened
automatically it snaps directly at
400 RT
the line reel. Proceed as follows:
A) Unplug the mains plug!
270 RT
B) Remove the line reel as
described under Point 8.1.
C) Pull the transparent plastic
ring over the line reel
(Figure M).
or maintained properly. The fol-
lowing table contains the most
common faults and remedies to
eliminate these faults. If you
D) The wound line is now
exposed. Unwind the line
approx. 12 cm and insert
it into the notch of the reel
(Figure N).
E) Thread the end of the line
through the eye of the trans-
parent plastic ring and fit
the ring back onto the reel
(Figure O).
F) Insert the line reel again as
described under Point 8.1.
Hold the Lawn Trimmer in the
normal working position before
you switch it on again.
We expressly point out that in
accordance with product liability
laws, we are not liable for any
damage caused by our units if
this damage is due to improper
repair or if parts exchanged are
not original parts supplied by
the manufacturer or parts
approved by the manufacturer,
and if the repairs were not car-
ried out at a technical service
centre or by an authorised
specialist. The same applies to
spare parts and accessories.
Care
Please ensure that the air vents
in the motor housing are always
kept free of dirt. Remove grass
and dirt from the safety cover
using a dry cloth or brush after
use.
Storage
We recommend hanging storage
to avoid unnecessary stress on
the cutting head.
have any other problems,
please contact your nearest
service centre authorised by
the manufacturer, or your

Publicidad

Tabla de contenido

Solución de problemas

loading

Este manual también es adecuado para:

400 rt duotipp

Tabla de contenido