General Power Tool Safety Warnings - Ryobi JG001 Manual Del Operador

GENERAL POWER TOOL SAFETy WARNINGS

WARNING
Read all safety warnings and instructions. Failure to
follow the warnings and instructions may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
power tool.
WORk AREA SAFETy
 keep work area clean and well lit. Cluttered or dark
areas invite accidents.
 Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases
or dust. Power tools create sparks which may ignite the
dust or fumes.
 keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
ELECTRICAL SAFETy
 Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
 Avoid body contact with earthed or grounded surfaces
such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body is
earthed or grounded.
 Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of electric
shock.
 Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. keep cord away
from heat, oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electric shock.
 When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric
shock.
 If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
NOTE: The term "residual current device (RCD)" may
be replaced by the term "ground fault circuit interrupter
(GFCI)" or "earth leakage circuit breaker (ELCB)."
 Use battery only with charger listed.
MODEL BATTERy PACk
(Li-ion) CB120L
JG001
(Ni-Cd) CB120N
PERSONAL SAFETy
 Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a
power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of inattention
 Use personal protective equipment. Always wear eye
 Prevent unintentional starting. Ensure the switch is in
 Remove any adjusting key or wrench before turning
 Do not overreach. keep proper footing and balance
 Dress properly. Do not wear loose clothing or jewellery.
 If devices are provided for the connection of dust
 Do not wear loose clothing or jewelry. Contain long
 Do not use on a ladder or unstable support. Stable
POWER TOOL USE AND CARE
 Do not force the power tool. Use the correct power
 Do not use the power tool if the switch does not turn
 Disconnect the plug from the power source and/or
 Store idle power tools out of the reach of children and
CHARGER
CH120L, C120D
 Maintain power tools. Check for misalignment or
C120N, C120D
3 — English
while operating power tools may result in serious personal
injury.
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites
accidents.
the power tool on. A wrench or a key left attached to
a rotating part of the power tool may result in personal
injury.
at all times. This enables better control of the power tool
in unexpected situations.
keep your hair, clothing and gloves away from moving
parts. Loose clothes, jewellery or long hair can be caught
in moving parts.
extraction and collection facilities, ensure these are
connected and properly used. Use of these devices can
reduce dust-related hazards.
hair. Loose clothes, jewelry, or long hair can be drawn
into air vents.
footing on a solid surface enables better control of the
power tool in unexpected situations.
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
do not allow persons unfamiliar with the power tool
or these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
binding of moving parts, breakage of parts and any
other condition that may affect the power tool's
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.