Maintenance And Cleaning - stayer E125M Manual De Instrucciones

Switching on: On/Off switch 7 to position I.
Switching off: On/Off switch 7 to position O.
Test run: Before using for the first time, run machine
for at least 5 minutes without load.Dress a
new grinding wheel with a dressing stone.
6.- Grinding Wheel Replacement
Pull the plug from the socket.
Loosen the 3 screws of the protective cover 1and remove
the protective cover. Unscrew the clamping nut 2 while
holding the grinder spindle 5 with an open ended spanner
on the spanner surfaces of the respective side.
Caution: Grinder spindle 5 has left-
handedthreads on the left side!
Remove clamping flange 3 and grinding wheel.
The mounting of the new grinding wheel is performed in the
reverse order. Press the protectivecover 1 on firmly and
tighten the screws.
Testing new grinding wheels
Use only original Stayer grinding wheels!
Damage to the original packaging could indicate defects.
Check before mounting that the grinding wheel is free of
damage.
The maximum allowable RPM of the grindingwheels
used must at least correspond to the maximum no-load
RPM of the machine.
Test run new grinding wheels at least 5 min-utes and
then dress with the dressing stone (accessory).
Dress used, out of round grinding wheelswith the
dressing stone (accessory) beforecontinuing to use.
7.- Operating Instructions
Lay the workpiece to be ground on the toolrest 11 and press
lightly against the grinding wheel. To achieve optimal
grinding results, movethe workpiece lightly back and forth.
This also contributes to uniform wear of the grinding wheel.
Cool the workpiece in water from time to time.
For grinding hard metal workpieces, use siliconcarbide
C grinding wheels (accessory).
Protect the grinding tool from impact, shock andgrease.
Do not work with materials containing asbestos.

8.- Maintenance and Cleaning

Before any work on the machine itself, pull the mains plug.
Always keep the machine clean.
If the machine should fail despite the care taken in
manufacturing and testing procedures, repairshould be
carried out by an aftersales service centre for Stayer power
tools.
In all correspondence and spare parts orders,please
always include order number given on the name plate of
ENGLISH
13
the machine.
WARNING! This appliance must be earthed.
9.- Repair Service
The technical service will provide you advice regarding
questions you may have on the repair and maintenance of
your product as well as on spare parts. You may also obtain
exploded views and information on spare parts on the
internet under:
info@grupostayer.com
Our team of technical advisors will be glad to guide you
regarding acquisition, application and adjustment of
products and accessories.
10. Guarantee
Guarantee card
Included in the documentation that accompanies this
equipment, you should find the warranty card. You should
fill out the card completely and return to vendor with a copy
of purchasing receipt or invoice and you should receive a
receipt.
Note: If you cannot find the warranty card within the
documentation, you must ask for it through your
supplier.
The warranty is limited only to manufacturing defects and
expire if pieces have been removed o
11.- Environmental Protection
Recycle raw materials instead of disposing
aswasteThe machine, accessories and
p a c k a g i n g s h o u l d b e s o r t e d f o r
environmental-friendly recycling.These
instructions are printed on recycled paper
manufactured without chlorine.The plastic
components are labelled for categorized recycling.
12. - Technical Features
P = Power
1
n = Drafts in vacuum
0
Ø = Wheel dimensions
m = Mass
L = Acoustic pressure level
WA
L = Acoustic power level
A
P
Valori determinati 61029.El livello di secondo EN pressione
sound, typical, misurato a di-type filter, è nella tabella delle
caratteristiche. Il livello di rumore, with può il lavoro
macchina during superare gli 85 dB (A).
Utilizzare protezione dell'udito!
13