Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
CHECKING OIL LEVEL
Always purchase those products labeled "Hydraulic Jack Oil". Do not use brake or transmission fluids, as they can damage the seals.
1. Turn release valve counterclockwise to allow ram to fully retract.
2. Remove fill plug.
3. With jack in vertical position, proper oil level should be even with bottom of hole. If low, fill with NEW, clean hydraulic jack oil and recheck
level. Do not overfill!
4. Replace filler plug.
5. Check jack operation.
At this time, consult Troubleshooting section for air removal procedure to purge air from system..
TROUBLESHOOTING
System Air Purge
1. Turn release valve counterclockwise one full turn to open.
2. Pump handle eight full strokes.
3. Turn release valve clockwise to closed position.
4. Pump handle until the lift arm reaches maximum height and continue to pump several times to remove trapped air in the ram.
5.
Turn release valve counterclockwise one full turn to open and allow lift arm to retract.
6. Close release valve and check for proper pump action. It may be necessary to perform the above more than once to assure air is evacuated totally.
Jack will not lift to full height:
Low oil level
Jack will not hold load:
Release valve not closing
Dirt in hydraulic jack oil or pump valves not sealing
Refer to Air Purge Section
Lift arm will not lower:
Cylinder ram binding
Release valve broken
Parts worn
Jack feels spongy when lifting:
See Air Purge section
1. Lower the Boom (B) to its lowest position.
2. Remove Clips (17) and Pins (13) holding Leg Extensions (G) to the Base (F). Remove leg extensions from base and position them vertically in
the storage pockets located slightly to the rear of the front pair of Caster Wheels (16) on base.
3. Reinstall the clips, pins and set screws removed in step 2 to secure the leg extension safely in the vertical position and to prevent the loss of parts.
!!WARNING!!
OTHER SYMPTOMS
STORAGE
4
GRUE D'ATELIER STOCKAGE DE 2 TONNES
SPECIFICATIONS
Capacité
Longueur
Largeur
Hauteur
27
26
A
8
21
G
15
15
LISTE DES PIÈCES
N°
Description
Qté.
A
Rallonge de la flèche
1
B
Flèche
1
C
Mât vertical
1
D
Appuis de mât
2
E
Vérin hydraulique
1
F
Socle
1
G
Rallonge de pied
2
1
Boulon, M16 x 100
2
2
Rondelle, M16
3
3
Écrou, M16
3
4
Boulon, M16 x 100
1
5
Rondelle, M16
4
6
Écrou, M16
4
7
Boulon, M16 x 100
1
8
Boulon, M14 x 90
1
9
Rondelle, M16
1
10
Écrou, M16
1
2 Tonnes (1818 Kg)
68-1/2" (174 cm)
39-3/8" (100 cm)
57" (145 cm)
6
5
B
27
26
24
11
10
9
23
14
3
E
2
C
19
7
6
D
5
25-18-20
1
4
6
17
5
2
3
12-18-16
13-17
22
16
13
25
18
12
N°
Description
Qté.
11
Boulon, M16 x 120
12
Boulon, M8 x 12
13
Goupille (petit)
14
Poignée de poussée
15
Roue (3.5"/8,89cm)
16
Roulette pivotante (3"/7,62cm)
17
Agrafe
18
Rondelle frein, M8
19
Poignée
20
Roulette pivotante (3.5"/8,89cm) 2
21
Crochet et chaîne
22
Boulon, M16 x 100
23
Boulon, M14 x 90
24
Boulon, M16 x 90
25
Boulon, M8 x 16
26
Rondelle, M14
27
Écrou, M14
5
18
12
F
20
18
1
12
4
1
2
2
4
20
1
1
2
1
1
8
2
2
Publicidad
Tabla de contenido
