Publicidad
Idiomas disponibles
Idiomas disponibles
WARNING:
Do not put the screw through the plastic housing of the unit as
this will permanently damage the unit and cause a potential electrical hazard.
To mount the unit Using the Magnetic Discs:
The magnetic discs in the bottom of the unit allow you to position the battery
charger on any flat, secure metallic surface.
Using the Hanging Hook:
The hanging hook can also be used to conveniently position the unit.
CAUTION –
TO REDUCE THE RISK OF PRODUCT DAMAGE:
• When the charger is hung by the hanging hook or attached using the magnetic
discs, do not shake the charger or object that it is hanging from or attached to.
Do not hang the charger from or attach the charger to any electrical wires or
anything that it is not secure.
• Only use the hanging hook or magnet discs for hanging or positioning the
charger. The hanging hook and magnetic discs are not intended to support
additional weight. Do not attach or hang anything additional to the charger or
risk of breakage may occur.
OPERATING INSTRUCTIONS
WARNING –
TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:
• Always disconnect the AC plug from the AC outlet first before disconnecting the
charger from the battery to be charged.
• Ensure that all installation, operating instructions and safety precautions are
understood and observed; then follow the steps outlined in the appropriate
section ("Charging a battery installed in a vehicle" or "Charging a battery that has
been removed from a vehicle").
Charging Using the Supplied Battery Clips
The charger's output leads have color-coded battery clamps (RED–POSITIVE and
BLACK–NEGATIVE).
1. Make sure the battery charger is unplugged from any power source and is not
connected to a battery.
2. Insert the double barrel tip of the battery clamp cable into the unit's Double
Barrel Charger Connector (male-to-female and female-to-male).
3. Connect the battery clamps to the battery and position the unit as far away
from the battery as possible, following the appropriate directions in the
"Preparing to Charge" Section at the front of this manual.
4. Insert the AC plug of the battery charger into a (powered) standard North
American 120 volt 60Hz outlet. The Charging/Charged LED will flash green to
indicate the unit is in charging mode.
Notes:
If the clamps are incorrectly connected with regard to polarity, the Reverse Connection LED will
light. Unplug the charger; then remove the clamps. Reconnect the clamps properly.
If the Charging/Charged LED did not come on, check the connection to the battery and the
AC outlet. If the clamps are properly connected to the battery and a functional AC outlet,
the battery may be in fault condition. Manufacturer suggests to have the battery tested by a
qualified battery service technician.
5. When the Charging/Charged LED lights solid, the charging process is complete.
When disconnecting the battery charger, first unplug the AC cord, remove the
clamp from the vehicle chassis, and then remove the clamp from the battery
terminal.
Connecting and Charging with the Terminal Rings
CONNECTING THE CHARGER WITH TERMINAL RINGS
The charger's output leads have crimped, color-coded terminal rings (RED-POSITIVE
and BLACK-NEGATIVE). These rings connect directly to the corresponding connectors
on the battery posts.
NUT
CONNECTOR
TERMINAL RING
BOLT
1. Remove the nuts from the bolts of the battery post's connectors.
2. Position the RED terminal on the bolt of the POSITIVE battery post connector.
BC209W_ManualENSP_100920.indd 6-7
BC209W_ManualENSP_100920.indd 6-7
3. Position the BLACK terminal on the NEGATIVE post connector; then replace
the nuts.
IMPORTANT: If there is any problem connecting the output leads, check with a
reputable auto supply store or contact the Customer Service Department toll-free at
1-877-571-2391 for assistance in finding an appropriate connection device for your
particular application.
CHARGING WITH THE TERMINAL RINGS
1. Make sure the battery charger is unplugged from any power source and is not
connected to a battery.
2. With the Terminals Rings properly connected to the battery posts, connect
the Terminal Ring connector with the unit's Double Barrel Charger Connector
(male-to-female and female-to-male) and position it as far away from the
battery as possible.
3. Insert the AC plug of the battery charger into a (powered) standard North
American 120 volt 60Hz outlet. The Charging/Charged LED will flash green to
indicate the unit is charging mode.
Notes:
If the Terminal Rings are incorrectly connected with regard to polarity, the reverse polarity LED
will light. Disconnect the charger, disconnect the Terminal Rings, then reconnect them properly.
If the Charging/Charged LED did not come on, check the connection to the battery posts
and the AC outlet. If the Terminal Rings are properly connected to the battery posts and a
functional AC outlet, the battery may be in fault condition. Manufacturer suggests to have the
battery tested by a qualified battery service technician.
4. When the Charging/Charged LED lights solid, the charging process is complete.
When disconnecting charger, disconnect AC cord, and then remove the Terminals
Rings from the battery posts.
CARE AND MAINTENANCE
Cleaning and Storage
To reduce the risk of electric shock, unplug the battery charger from the outlet
before attempting any maintenance or cleaning. Turning off the controls will not
reduce this risk.
• Store the unit in a clean, dry, cool place when not in use.
• Clean the unit casing and cords (as necessary) with a dry cloth. Ensure that unit is
completely disconnected from battery and power source before cleaning. Do not
immerse the appliance in water.
• To maintain the operating condition and maximize the life of the charger cords,
always coil them loosely for storage. Do not wrap them around the unit or crimp
them with a tight band.
TROUBLESHOOTING
Unit not charging
• Check that the battery charger/maintainer is properly connected to a live 120 volt
AC outlet.
• Make sure all connections are secure.
• Check the connections for correct polarity.
• If the battery to be charged or maintained has fallen below 2 volts, the battery
cannot be recharged with this unit.
• If the maintainer does not detect battery voltage, the unit will not operate.
ACCESSORIES
Recommended accessories for use with this unit may be available from the
manufacturer. If you need assistance regarding accessories, please contact
manufacturer at 1-877-571-2391.
WARNING:
The use of any accessory not recommended for use with this
appliance could be hazardous.
SERVICE INFORMATION
Whether you need technical advice, repair, or genuine factory replacement parts,
contact the manufacturer at 1-877-571-2391.
FULL ONE-YEAR HOME USE WARRANTY
The manufacturer warrants this product against defects in materials and
workmanship for a period of ONE (1) YEAR from the date of retail purchase by the
original end-user purchaser ("Warranty Period").
If there is a defect and a valid claim is received within the Warranty Period, the
defective product can be replaced or repaired in the following ways: (1) Return the
product to the manufacturer for repair or replacement at manufacturer's option.
Proof of purchase may be required by manufacturer. (2) Return the product to the
retailer where product was purchased for an exchange (provided that the store is a
participating retailer). Returns to retailer should be made within the time period of
6
the retailer's return policy for exchanges only (usually 30 to 90 days after the sale).
Proof of purchase may be required. Please check with the retailer for their specific
return policy regarding returns that are beyond the time set for exchanges.
This warranty does not apply to accessories, bulbs, fuses and batteries; defects
resulting from normal wear and tear, accidents; damages sustained during shipping;
alterations; unauthorized use or repair; neglect, misuse, abuse; and failure to follow
instructions for care and maintenance for the product.
This warranty gives you, the original retail purchaser, specific legal rights and you
may have other rights which vary from state to state or province to province. This
product is not intended for commercial use.
Be sure to register your product at https://www.baccusglobal.com/registration to
receive important product information, special promotions and offers, and more.
SPECIFICATIONS
Input:
120V AC, 60Hz, 0.6A
Output:
12V DC, 2A
Imported by Baccus Global LLC,
Baccus Global LLC, 621 NW 53rd St., Suite 450, Boca Raton, FL 33487
www.Baccusglobal.com 1-877-571-2391
RD100920
7
10/9/2020 11:34:54 AM
10/9/2020 11:34:54 AM
Publicidad
