Smeg K9998 Instrucciones Para Instalación Y Uso página 3

Then fit the charcoal filter (Fig. 15) by inserting the two filter clips in the slots and turning the filter towards the inside
of the hood.
Fig. 13: grip the knob and push it towards the opposite side of the filter and turn the filter outwards (Fig. turn the filter
outwards. Proceed with the assembly of the charcoal filter by inserting the 2 flaps of the filter into the special slots
(Fig. 16) and turning the filter inwards (Fig. 17).
Fig.14: Turn the panel gripping it from the font part of the hood. Remove the grease filters by pushing the catch towards
the rear of the hood and turning the filter outwards.
Then fit the charcoal filter:
Fitting the rectangular charcoal filter (Fig. 15): Insert the 2 charcoal filter clips in the slots and turn the filter towards
the inside of the hood.
Fitting the panel charcoal filter (Fig. 18): remove the metal filter clips (M), insert the charcoal filter and reassemble
the filter clips.
Fixing to the wall: for fixing to the wall refer to the instructions for the ducting version (see points 1, 2), then continue
with the instructions below.
Fixing the telescopic flues: - Adjust the width of the support bracket of the telescopic flue by means of the screws
as shown in Fig. 7. - Then, by means of the screw anchors and screws (F) provided, fix the bracket to the ceiling in such
a way that it is positioned along the axis with your hood (Fig.8). - Mount the flange on the hood in correspondence to the
air outlet point (Fig. 19). - Take the air baffle and fit a flexible pipe to it (125 mm diameter) locking it with a metal hose
clamp (pipe and clamps are not provided). Fit the air baffle to the upper flue (Fig. 20) with 4 screws.
- Connect the flexible pipe to the flange on the air vent (Fig. 21). - Plug in the hood. - Insert the extension flues setting
them on the hood; extend the upper flue to the ceiling and secure with the 2 screws H (Fig. 11).
OPERATION
Depending on the model, the unit is equipped with the following controls:
Controls shown in Fig. 22:
Key L: light switch. Key A : B = Motor ON/OFF switch - Speed I
Key 2: B = Motor ON/OFF switch - Speed I
Key 3: B = Motor ON/OFF switch - Speed I
Key 4: B = Motor ON/OFF switch - Speed I
Filter alarm: after about 30 hours of operation, with the motor off, the speed keys (keys 1, 2, 3 and 4) flash for 30
seconds to indicate the anti-grease filters need cleaning. After cleaning the anti-grease filters (and/or replacing the
charcoal filters), restart the hour counter (RESET) by pressing key C during filter alarm display.
Timer 5'; the timer can be started (switch-off delayed by 5 minutes) by pressing one of the speed keys for 2 seconds
(key 1, 2, 3 or 4) when the motor is running; the selected speed key starts flashing.
Controls shown in Fig. 23:
Button A: light switch.
Button B: first speed motor ON/OFF switch.
Button C: second speed switch.
Button D: third speed switch.
Controls shown in Fig. 24:
Key L: light switch.
Key 1: activates/deactivates the sensor (AUTOMATIC or MANUAL mode). In Automatic mode the sensor is active
and the speed of the motor increases or decreases depending on the smoke.
- signals the filter alarm (with motor off)
Key 2: Motor ON/OFF switch - Speed I.
Key 3: Motor ON/OFF switch - Speed II.
Key 4: Motor ON/OFF switch - Speed III.
Filter alarm: after about 30 hours of operation, with the motor off, the speed keys (keys 1, 2, 3 and 4) flash
for 30 seconds to indicate the antigrease filters need cleaning. After cleaning the anti-grease filters (and/or replacing
the charcoal filters), restart the hour counter (RESET) by pressing one of the speed keys for 2 seconds during
filter alarm display.
SENSOR SENSITIVITY: When the sensor is on, the hood automatically starts working when any smell, vapour,
smoke or heat is detected during cooking. The sensor sensitivity can be changed according to need.
For example: very sensitive when using an electric hob or little sensitive when using a gas hob. Change the
sensitivity by simultaneously pressing key L and key 1.
The sensitivity selected will be set. Using the keys 2,3,4 you can set the desired sensitivity. Store the new
sensitivity by pressing key 1.
Grease filters: pay special attention to the grease filters, that must be cleaned at regular intervals. Wash the
grease filter/s with neutral detergent.
Filter cleaning frequency:
If the model purchased by you has the controls represented in Fig. 22: the grease filters must be cleaned about every
30 hours of operation (when, with the motor off, the 4 speed keys flash). Once the clean filters have been remounted,
keep one of the 4 keys pressed for 2 seconds (during flashing) to start the hour count again.