Safety Rules; Technical Data - Action Activejet Selected WSS-130B Manual De Instrucciones

GB
Metal fan Activejet Selected WSS-130B / WSS-130C / WSS-130BD / WSS-130CD / WBS-30B / WBS-30C / WBS-30BD / WBS-30CD
NOTE:
Before using the fan, read the Instruction Manual. We recommend that you keep this manual for future reference.
While the fan is in operation, it is advisable to follow the basic safety rules to avoid a fire, electric shock and mechanical damage to the body.
Observing the instructions and recommendations contained in the Instruction Manual extends the device's service life.

SAFETY RULES:

1. Do not attempt to repair the device yourself.
2. Keep the device work area in order.
3. Keep the device away from moisture and water, explosive and flammable substances and particles. Failure to follow these rules may result
in a fire or electric shock. Excessive dusting of the device may lead to overheating of the motor and permanent damage to the fan.
4. It is forbidden to use wires with the plug that is not original or any adapters.
5. Take care of the power cord; do not use the cord to move the device, pull it or pull the plug from the wall. Protect the cable from heat,
mechanical damage, oil.
6. Do not put your fingers or devices in the air outlet/inlet grille. Take care that long hair is not screwed into the propeller of the device in use.
7. The device is not intended for people with limited physical, sensory or mental abilities. Children under the age of 8 and people
with restrictions may use the device only under the supervision of a person responsible for their safety.
8. Do not cover the device, for example, with clothing.
9. Make sure that the power supply complies with the voltage specified for the device (220-240V ~ / 50-60 Hz).
10. Installation, disassembly, cleaning and maintenance of the fan may take place only after removing the plug from the socket.
11. Do not leave the switched on device unattended.
12. The device is intended for use indoors, in clean and dust free rooms. The fan should be placed on a hard, flat surface at a distance of 0,3-1m
from all objects, such as radiators, other electrical appliances, furniture and curtains.

TECHNICAL DATA:

Model: WSS-130B, WSS-130C, WSS-130BD, WSS-130CD
Voltage and frequency: 220V-240V,50Hz-60Hz
Power: 50W
Mass: ~7.0 kg
INSTALLATION:
1. Start the installation by connecting the fan base with the telescopic tube. Remove the base mounting screw (11) and the mounting nut (6),
as in fig. 2. Fit the telescopic tube end into the indentation in the upper part of the fan base (5). Put on the mounting nut (6) and tighten it
with the base mounting screw (11), as in fig. 3. Place the assembled base on hard surface.
2. Remove the angle adjustment knob (9) and remove the angle adjustment screw (3), as in fig. 2. Use a screwdriver to remove the small angle
screw (10) and unscrew the angle knob (2) which is under the engine housing, as in Fig. 4.
3. Fit the engine housing head into the matching grooves in the upper part of the telescopic tube and proceed as in fig. 5.
4. Use a screwdriver to screw in the small angle screw (10), as in fig. 6. Next, screw in the angle adjustment knob (9), as in fig. 7
CONNECTION TO THE NETWORK:
After making sure that the power supply is compatible with the voltage specified on the device, connect the device to a properly installed electrical
outlet with a protective bolt.
USE:
Make sure that the fan is placed on a flat and level surface away from other heat sources, at a sufficient distance from curtains and other
lightweight materials that the air rush could pull into the fan.
1. To control the device use the speed adjustment knob (8).
Position 0 - turned on
Position I - low speed
Position II - medium speed
Position III - high speed
Model: WBS-30B, WBS-30C, WBS-30BD, WBS-30CD
Voltage and frequency: 220V-240V,50Hz-60Hz
Power: 35W
Mass: ~4.4 kg
Metal fan Activejet Selected WSS-130B / WSS-130C / WSS-130BD / WSS-130CD / WBS-30B / WBS-30C / WBS-30BD / WBS-30CD
2. To set the fan head at the desired angle, first loosen the angle knobs (2) and (9), set the angle and then tighten the parts (2) and (9).
3. To activate oscillation, press the oscillation button (7). To stop oscillation at the desired position, release the oscillation button (7).
4. Fan height adjustment ( in WSS-130B, WSS-130C, WSS-130BD, WSS-130CD models ). To set the fan at the desired height, loosen the height
adjustment knob (4), slide the upper part of the telescopic tube in or out and tighten the height adjustment knob (4).
We recommend unplugging the fan from the power supply in the event of storm or a long break in use.
WARRANTY CONDITIONS:
1. Activejet fans are covered by a 24-month warranty. The time covered by the warranty is calculated from the date of purchase of the product.
2. The warranty covers defects caused by factory-based defective materials, improper assembly (factory), manufacturing errors.
3. The warranty does not cover defects resulting from: use contrary to the purpose and recommendations of the Instruction Manual,
overloading the device leading to the damage of the engine or mechanical transmission components, making repairs on one's own
or by unauthorized persons, making construction changes, physical and chemical damage caused by external factors and damage caused
by improper assembly as well as mechanical damage.
4. The warranty does not cover parts subject to natural wear during operation: thermal fuses, electrostatic brushes, V-belts, tool holders,
accumulators, working tips of power tools.
5. The nameplate of the device should be legible. The returned/claimed product should be carefully protected against damage in transit.
As far as possible, provide the product in the original packaging.
6. In order to make use of the warranty, you should report to the point of purchase along with the proof of purchase (receipt, invoice).
7. The warranty is carried out by the sole distributor and owner of the brand: Action SA, Zamienie, ul. Dawidowska 10, 05-500 Piaseczno, Poland.
MEANING OF THE SYMBOL:
A crossed out trash bin symbol means that the device should not be disposed of in normal waste containers.
It is the responsibility of the user to hand over the used equipment to the collection points for the recycling of waste
generated from electrical and electronic equipment.
CE DECLARATION OF CONFORMITY:
The device has been manufactured in accordance with the applicable European standards, including the relevant directives and regulations
in force in the European Union for electrical products. This means that the product complies with the principles of safe use, health
and environmental protection.
GB