Denios GS 305 Manual Del Usuario página 13

When storing full pressurised gas cylinders outside, there should be a safety distance of at least 5 m between the
gas cylinder container and any surrounding buildings (see TRG 280, section 5.3.4). The container must be
enclosed by a 2m (at least) wall to prevent flammable substances from escaping. (The walls of the pressurised
gas cylinder cabinet do not offer sufficient protection).
Assembly
The ground must be level and suitable to support and anchor the gas cylinder cabinet to.
Gas cylinder cabinet with base GS 305-B
(Also see overview diagram of the cabinet (Assembly GS 305-B) p. 7 and parts list p. 11)
1. Align the location bars (52) and the centre support (9) at diagonal right angles as shown in Fig. 1 „securing
the base to the floor".
2. Screw screws(29) through the centre of the bars (52) to secure them to the floor (see Fig. 2 „securing the
base to the floor").
3. Place the side frames (1) on the location bars (52) and screw them in place using hexagonal screws (54, 55,
56, 57) (see Fig. 3 „assembling the base for the GS 305- model").
4. Screw the centre support (9) to the location bars (52) using sunken head screws (53, 56, 57) (see Fig. 4 „unit
Y").
5. Screw the rear panel (7) to the side frames (1) and the centre support (9) using hexagonal screws (22, 23,
24).
6. Screw the two part front roof brace (4 and 6) together using round head screws (5 und 5.1) and screw them
the side frames using hexagonal screws (22, 23, 24), (see Fig. 5 „assembling the front roof brace").
Fit the 4 roof sheet metal elements (14) on top of the cage in such a way, that they overlap themselves
evenly. The outside upper crimpings must seize over the side frames (1) and the lower crimpings have to
rest on the front roof brace and the rear panel.
The roof overhang shall amount to approx. 500 mm in front and approx. 50 mm in the back.
Secure the roof panel to the roof brace and the rear panel using self drilling screws (15). It may be screwed
only into the lower crimpings of the trapezoidal sheet metal
Secure the U channels (14.1 and 14.2) to the edge of the roof at the front using self drilling screws (15).
It may be screwed only into the upper crimpings of the trapezoidal sheet metal.
7. Secure the bottom of the hinge (11) to the side frames using hexagonal screws (22, 23, 24), (see Fig. 6
„hinges").
8. Place the mortise lock (16) on door 2 and screw it in place using self-tapping screws (20). Put the profile half
cylinder (17) on the lock, then add on the protective plate (19), plastic plugs (21) and the door handle (18).
Secure the protective plate in place using sunken head screws (20) (see Fig. 7 „lock").
9. Secure the bolt (43) to door 3 using sunken head screws (20) (see Fig. 8 "wing door").
10. Assembling the doors: Hang door 3 on the container first, followed by door 2. Tap the steel pin (13) into the
top part of the hinge on door 2 and hang the door on the container. Tap the smaller pin (12) into the bottom
of the hinge. Align the door, adjust the screws in the hinges or, if necessary, push the side frames lightly.
11. Put the grid spports (51) and the grid (50) in place.
12. Tighten all screws, if necessary.
13. Stick the following signs on a board (47) on the door, „smoking and open flame prohibited, and no access
to unauthorised personnel" (45 and 46).
14. If the gas cylinders are going to be stored without gas cylinder pallets, the gas cylinder holder (8) must be
secured to the rear panel using hexagonal screws (23, 24, 25) (see Fig. 9 gas cylinder holder). The support
for the gas cylinder holder (10) should be placed under the seam in the rear panel and screwed to the holder
(8) using hexagonal screws (23, 26). The securing chain (28) should be fastened to S hooks (27) pushed
through drill holes in the gas bottle holder and hung on the mesh side panels..
Gasflaschenschrank GS 305-B / GS 305
115861 / 11586
Seite 13 von 28 Seiten Ausgabe 06/2007