General Safety - Husky HDS420 Instrucciones De Uso

Multi-Purpose Spray Gun
Spray Gun Terms
(Continued)
type of operation is used with a
compressor equipped with a tank or
with a large factory air system. Do not
use with a continuous run compressor
that does not have a tank.
VISCOSITY – A measurement of the
resistance of the flow of a liquid.
ATOMIZATION - Conversion of liquid
to spray droplets (mist).
PATTERN CONTROL KNOB – Used to
form the proper pattern (size and
shape) of material as it is sprayed from
the gun to the work piece.
FLUID CONTROL KNOB – Used to
control the amount of material being
mixed with air.
PAINT TANK – An auxiliary pressurized
paint reservoir that allows continuous
spraying of large amounts of paint
without stopping for refills as with a
canister. It also allows using the spray
gun at any angle or orientation.

General Safety

1. Read all manuals
included with this
product carefully. Be
thoroughly familiar
with the controls and the proper
use of the equipment.
2. Follow all local electrical and safety
codes as well as in the United
States, the National Electrical Codes
(NEC), Occupational Safety and
Health Act (OSHA) and the
Environmental Protection Agency
(EPA).
WARNING
!
Use a face mask/respirator
and protective clothing
when spraying. Always
spray in a well ventilated
area to prevent health and fire hazards.
Refer to Material Safety Data Sheets
(MSDS) of spray material for details.
DANGER
!
Never spray closer than 25
feet to the compressor! If
possible, locate compressor in separate
room. Never spray into the compressor,
compressor controls or the motor.
3. Do not smoke or eat when spraying
paint, insecticides, or other
flammable substances.
WARNING
!
Do not spray flammable
materials in vicinity of
open flame or near
ignition sources. Motors, electrical
equipment and controls can cause
electrical arcs that will ignite a
flammable gas or vapor. Never store
flammable liquids or gases in the
vicinity of the compressor.
4. When spraying and cleaning,
always follow the instructions and
safety precautions provided by the
material manufacturer (Refer to
MSDS).
WARNING
!
toxic chemicals, fertilizers or pesticides.
Using these materials could result in
death or serious injury.
5. Keep visitors away and NEVER
allow children or pets in the work
area.
WARNING
!
or anyone else or serious injury could
occur.
MANUAL
6. Always work in a clean
environment. To avoid injury and
damage to the workpiece, do not
aim the spray gun at any dust or
debris.
WARNING
!
Do not use pressure that
exceeds the operating
pressure of any of the
parts (hoses, fittings, etc.) in the
painting system.
CAUTION
!
Bursting air hoses may cause injury.
Examine air hoses regularly and replace
if damaged.
7. Always use a pressure regulator on
the air supply to the spray gun.
NOTICE
water/oil removal equipment may
result in damage to machinery or
workpiece.
Set Up
USE OF AIR CAPS
Internal Mix—Generally
used with slow drying,
heavy bodied materials
and for faster material
application. NOT to be used with fast
drying paints and lacquers which will
clog the opening in the air cap.
INTERNAL MIX CAPS MUST BE USED
WITH PRESSURE FEED operation.
External Mix—Used for
quick drying, light bodied
materials such as lacquers
and synthetic enamels.
Better for finer finish work. THESE
CAPS CAN BE USED WITH EITHER
SIPHON OR PRESSURE FEED.
FAN DIRECTION
The direction of the fan (horizontal or
Do not spray acids,
vertical) can be changed by loosening
corrosive materials,
the lock ring and turning the air cap 90
degrees (See Figure 1). Hand tighten
lock ring after adjustment.
Never aim or
spray at yourself
FLUID FEED
This model is capable of pressure or
siphon feed. Standard set-up is
pressure feed mode; change to siphon
mode for a finer finish using light
materials. To change modes, remove
setscrew from the canister top and
place in the lower part of the gun
Keep hose away
head (See Figure 2).
from sharp objects.
Failure to install
appropriate
Figure 2
2
Air Cap
Horizontal Fan
Vertical Fan
Lock Ring
Figure 1
Place
setscrew
in lower
hole
Remove from
underside of
canister top