Kicker DDS12 Manual Del Propietário página 3

2008 DDS12 Box 4in1 a01.qxp 11/19/2009
Congratulations on your
KICKER purchase
Please record your purchase
information and keep your sales
receipt for validation of warranty.
The Kicker DDS12 loaded subwoofer enclosure was specially designed for "Livin' Loud" out in the
harsh automotive environment. The DS series was designed to offer booming bass at the best bargain
possible without compromising Kicker quality. The DDS12 is made of advanced materials and
construction techniques to maintain optimal performance for years to come.
CheckTheLoad
The DDS12 loaded subwoofer enclosure is internally wired for a 2 or 4 ohm load at the speaker-wire
connection terminal. Please refer to this terminal or the box packaging for your enclosure's specific
impedance. Check to see if your amplifier is optimized to drive this load.
DDS12Vented
The DDS12 vented enclosure combines KICKER's award winning line of subwoofers with computer-
modeled and human fine-tuned enclosures to offer a level of bass performance never before thought
possible from a commercially available, ready-to-install subwoofer system. The DDS enclosure is
available with two pre-loaded 12 inch DS subwoofers.
The location and orientation of your enclosure will affect the quality and quantity of the bass. Designed
for use in SUV and sedan type vehicles, these enclosures offer you several mounting options. The vent
opening in these enclosures can not be obstructed. At some frequencies most of the bass will come
out of the vent. Therefore we recommend you leave at least four inches (10cm) of clear space around
the vent.
If the enclosure is to be mounted all the way in the back of the vehicle, it works best to point the
woofer toward the front of the vehicle. Conversely, if the enclosure is going to be mounted closer to the
back seat, pointing the woofer toward the rear of the vehicle will give you the best results. These
guidelines pertain to enclosures mounted in the vehicle as outlined in Figure 1.
If it is more convenient to mount the enclosure along a side wall, put the enclosure on the left side of
the vehicle as outlined in Figure 2. This orientation will make the vent point toward the rear of the
vehicle and will produce the most low bass output. Remember to leave at least four inches (10cm) of
room between the enclosure and the back of the vehicle.
After determining the best mounting position, carefully check the areas where the mounting brackets
will be placed. Make sure the mounting screws will not puncture the gas tank, brake lines, wiring, or
interfere with any mechanical parts on the underside of the mounting surface. Turn the enclosure
upside-down, pre-drill the holes using a 7/64" (2.5mm) bit and attach the four mounting brackets to the
Please allow two weeks of break-in time for the subwoofer to reach optimum performance. To get the best performance
from your new Kicker subwoofers, we recommend using genuine Kicker Accessories and Wiring.
DSSUBWOOFERENCLOSURE
2
2:34 PM Page 2
DSSUBWOOFER
EnclosureOwner'sManual
Models:
DDS12
_________________________
Authorized Kicker Dealer:
_________________________
Purchase Date:
DDS12
_________________________
Enclosure Model Number:
_________________________
Enclosure Serial Number:
Front of
Vehicle
bottom of the enclosure using the supplied smaller screws. Each bracket must be positioned so the
rounded end protrudes approximately 3/4" (2cm) from under the cabinet to allow a screw to easily pass
through the bracket, securing the enclosure to the vehicle. With the enclosure right side up, securely
attach the enclosure to the vehicle with the supplied larger screws. See Figure 4. If the supplied
hardware is not applicable to your installation, some other means of securely attaching the enclosure to
the vehicle must be used.
Pro Tip: You are one ZX Mono-Amplifier and a few cables away from a slamm'in system!
The Kicker ZX line of mono-amplifiers make it easy to upgrade to rock-solid bass with your
existing or stock source unit. Please ask your dealer about Kicker ZX Amplifier upgrades.
Front of
Vehicle
Autogoods "130"
Figure 1
At least 4" (10cm)
from the vent
Rear mounting,
speaker faces
front of vehicle
Front mounting,
At least 4" (10cm)
speaker faces
from the vent
rear of vehicle
Figure 2
At least 4"
(10cm) from
the vent
Left side
mounting,
speaker faces
opposite side
of vehicle
3