Pprocedures For Use; Checks Prior To Start-Up; Feed Screw Loading; Switching The Appliance On And Off - Ravelli Touch Radio Manual De Instrucciones

Rev.0 17/05/2021
EN
Pag.24
⚠

PPROCEDURES FOR USE

If the chimney catches fire you must call the fire brigade immediately.
⚠

Checks prior to start-up

You have read and perfectly understood the contents of this instructions manual.
Before lighting the stove, you must ensure that:
• the pellet tank is full;
Operating phases of the appliance • the combustion chamber is clean;
• the fire door and ash drawer seals are functioning properly;
Modulation
• the electrical plug is connected correctly;
During the work phase, the appliance should reach the room temperature set; when this condition is met, the stove switches to
• all items that could burn (instructions, various adhesive labels) have been removed;
MODULATION mode in which fuel consumption and ventilation are minimum.
• the brazier, if removable, is correctly positioned in its housing.
��
During the first hours of use the paints used for the stove finish may release an unpleasant odour. You might also smell the
typical odour of metal parts subject to high temperatures. Make sure sufficient air circulation is guaranteed in the room. These
unavoidable inconveniences will disappear after the first hours of operation. To reduce your discomfort to a minimum, keep
the stove on for a few hours on low power and in the beginning, do not overload it, avoiding intense heating-cooling cycles
��
At the initial start-up, the paint finishes drying and hardens. Accordingly, to avoid ruining it, we advise you not to touch the
If you wish to detect the ambient temperature by means of an external thermostat (optional), this must be connected to
stove's painted surfaces at this time.
the appropriate connector on the rear side of the stove; and you will have to activate the reading in "SETTINGS - EN -
ABLE THERMOSTAT." On display appears the writing TON / TOFF based on thermostat request.

Feed screw loading

Before starting the stove for the first time, whenever the stove is in alarm "06 - Pellets finished", and in any case whenever the hopper
CONNECT AN EXTERNAL THERMOSTAT WITH A SIMPLE DRY CONTACT, THEREFORE, NOT POWERED. MORE-
has emptied completely, the initial feed screw loading is required. This phase serves to fill the pellet loading system so that, at the
OVER, WE RECOMMEND YOU USE A THERMOSTAT WITH A MINIMUM OFFSET OF 3°C IF YOU INTEND TO USE
time of ignition, the correct pellet loading takes place in the brazier.In the event that the feed screw operations are not carried out,
THE COMFORT CLIMA FUNCTION.
⚠
there may be stove ignition failures.
After loading the auger and before lighting the stove, always remember to empty the brazier and check that the brazier is
Comfort climate
⚠
clean. Never empty the brazier inside the hopper.
The activation of this function enables the stove to reduce pellet consumption by activating the modulation phases, after the desired
temperature has been reached. Subsequently, the stove checks that the temperature is maintained steady for a preset time. If this
⚠
After each maintenance operation, make sure that the brazier is positioned correctly in its seat.
condition is met, it automatically switches off, and on display appears the writing ECO.
The stove turns on again when the temperature drops below the set threshold.
In models with self-cleaning brazier it is not necessary to remove the pellets in the brazier: the pellets loaded are sufficient
Below are given the steps for accessing the relative menu.
for subsequent ignition.
MANUFACTURER
Press the "menu access"
Press the key
"access menu" to
button to access the
access
the
MENU screen.
MENU page

Switching the appliance on and off

From the "Home" screen, it is possible to switch the stove on and off by keeping the ON / OFF button pressed on the device for a few
Once you have accessed the Climate Comfort menu, it is possible to operate on the 3 types of settings dedicated to the function:
seconds. An acoustic signal will warn you that the appliance has switched on or off. In case it is not possible using your handheld you
⚠
can switch the appliance on / off using the appropriate button on the electronic board.
COMFORT CLIMA
Do not switch off the heater by unplugging the plug from the wall socket.
ENABLE COMFORT
��
The appearance of the "SET RDS" message indicates that the initial parameter testing and calibration procedure was not
RESTART DELTA
SHUTDOWN DELAY
carried out correctly. This indication does not imply blocking the stove (see SIGNALING POP UP section).
COMFORT CLIMA
ENABLE COMFORT
RESTART DELTA
SHUTDOWN DELAY
COMFORT CLIMA
ENABLE COMFORT
Use and maintenance manual Phandheld Touch Radio
User's manual HANDHELD TOUCH RADIO
MENU MENU
USER
USER
TECHNICIAN
ENGINEER
PRODUCER
Press the "confirm"
Press the key
button to access the
"confirm"
to access the
USER screen
USER page
USER
USER
SCREW FEEDING
LOADING AUGER
CHRONOTHERMOSTAT
AIR-PELLET SET
CHRONOTHERMOSTAT
STOVE STATE
SET AIR-PELLET
STOVE STATUS
ENABLE COMFORT
COMFORT CLIMA DELTA
SHUTDOWN DELAY
Vers. 01 of:07.04.14
LOADING AUGER USER
COMFORT CLIMA
SETTINGS
Press the "confirm"
Press the key "selection" for
"selection"
button to activate feed
to switch to the second page
screw rotation
of USER MENU and select
CLIMATE COMFORT.
ENABLE COMFORT
COMFORT CLIMA DELTA
SHUTDOWN DELAY
Pag.23