Royal Catering RCZC-1030-W Manual De Instrucciones página 6

Assembly of mesh on the bowl
(for RCZK-1500S-W model)
Unfold the mesh evenly (so that the end slightly overlaps
with the beginning) on the inside of the bowl and the use
the clips to secure the mesh.
XII. NOTES
1. Keep minors away from the machine.
2. The electric cable must not come near the hot
surface of the machine. Please ensure that the
electric cable and the connector plug do not come
into contact with water or any other liquids. DO
NOT use the device if the cable or the connector
plug is damaged.
3. Please DO NOT touch the surface of the machine
while it is in operation. DO NOT move the machine
while in operation.
4. Never touch the plug or cable with wet hands.
5. The temporary motor power of the device amounts
to 80%. It is best to avoid extremely long usage
periods. In order to prolong the life of the machine
the engine should rest for 20 minutes after every
hour of usage.
6. Before cleaning make sure that the plug is pulled out.
7. If the cotton candy turner doesn't make any cotton
candy, please turn off the device and remove burnt
sugar with soft cloth.
XIII. TRANSPORTATION AND STORAGE
Shaking, crashing and turning upside down of the device
should be prevented when transporting it. Store it in
a properly ventilated location with dry air and without any
corrosive gas.
XIV. CLEANING AND MAINTENANCE
• Disconnect from electricity when cleaning
equipment.
• Use cleaner without corrosive substances to clean
surface.
10
• Dry all parts well after cleaning before the device
is used again.
• Store the unit in a dry, cool location, free from
moisture and direct exposure to sunlight.
ATTENTION: Clean the device after use, regardless of
whether it was operated only once or a number of times.
For RCZC-1030-W/RCZK-1030-W/RCZK-1030-W-R
For efficient head cleaning, after use, pour approximately
150 ml of water into a hot and spinning head. The
evaporating water will clean the interior of the head.
Switch the machine off. Once the head has cooled down,
use a soft, damp cloth to wipe it clean. Failure to follow
these instructions may result in a build-up of caramelised
sugar, leading to defective operation of the machine (candy
floss will not spin, in extreme situations the head may be
permanently damaged).
The user shall be responsible for all damage resulting from
a failure to follow these instructions.
For the RCZK-1500S-W model
After you remove the bowl:
1. Unscrew and remove the carbon brushes.
2. Remove the caps, the locate the bolts by gently
spinning the head. Loosen the bolts.
3. Then remove the head.
4. Insert the head upside down into a container with
water as shown on the figure below
Max. water level
Leave head in the water for approx. 30 min. Make sure no
electrical parts of the head become wet.
5. Assemble the head back on the device: see steps
1 and 2.
XV. REGULAR CONTROL OF THE DEVICE
Regularly control whether the device is damaged. If it
should be damaged, please stop using it immediately and
contact your customer service to solve the problem.
What to do in case of a problem?
Please contact your customer service and prepare following
information:
Rev. 26.06.2017
• Invoice number and serial number (the latter is to be
found on the technical plate on the device).
• If relevant, a picture of the damaged, broken or
defective part.
• It will be easier for your customer service clerk to
determine the source of the problem if you give a
detailed and precise description of the matter. Avoid
ambiguous formulations like "the device does not
heat", which may mean either that it does not heat
enough or that it does not heat at all. The more
detailed your information, the better the customer
service will be able to solve your problem rapidly
and efficiently!
CAUTION: Never open the device without the
authorization of your customer service. This can lead to
a loss of warranty!
Manufacturer
expondo Polska sp. z o.o. sp. k.
ul. Dekoracyjna 3, 65-155 Zielona Góra | Poland, EU
Product name Candy Floss Machine
Model
Power
Voltage 230V~
Frequency 50Hz
Weight
Serial-No.
Production year
Design Made In Germany
expondo.de
Rev. 26.06.2017 11