Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
•
Never lay the tool down until the bit has come to a
complete stop. Moving bits could cause injury.
•
Do not strike jammed bits with a hammer to dislodge
them. Fragments of metal or material chips could dislodge
and cause injury.
•
Slightly worn chisels can be resharpened by grinding.
Do not overheat the bit (discoloration) while grinding
•
a new edge. Badly worn chisels require reforging. Do not
reharden and temper the chisel.
•
Do not use this tool to mix or pump easily combustible
or explosive fluids (benzine, alcohol, etc.).
•
Do not mix or stir inflammable liquids
labelled accordingly.
Additional Safety Information
WARNING: Never modify the power tool or any part of
it. Damage or personal injury could result.
WARNING: ALWAYS use safety glasses. Everyday
eyeglasses are NOT safety glasses. Also use face or
dust mask if cutting operation is dusty. ALWAYS WEAR
CERTIFIED SAFETY EQUIPMENT:
•
ANSI Z87.1 eye protection (CAN/CSA Z94.3),
•
ANSI S12.6 (S3.19) hearing protection,
•
NIOSH/OSHA/MSHA respiratory protection.
WARNING: Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities contains chemicals known to the State
of California to cause cancer, birth defects or
other reproductive harm. Some examples of these
chemicals are:
•
lead from lead-based paints,
•
crystalline silica from bricks and cement and other
masonry products, and
•
arsenic and chromium from chemically-
treated lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to filter
out microscopic particles.
Wear protective clothing and wash exposed areas
•
with soap and water. Allowing dust to get into your
mouth, eyes, or lay on the skin may promote absorption
of harmful chemicals. Direct particles away from face
and body.
•
Use the appropriate dust extractor vacuum to
remove the vast majority of static and airborne
dust. Failure to remove static and airborne dust could
contaminate the working environment or pose an
increased health risk to the operator and those in
close proximity.
•
Use clamps or other practical ways to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body is unstable and
may lead to loss of control and injury.
•
Air vents often cover moving parts and should be
avoided. Loose clothes, jewelry or long hair can be caught
in moving parts.
CAUTION: When not in use, place tool on its
side on a stable surface where it will not cause
a tripping or falling hazard. Some tools with large
battery packs will stand upright on the battery pack
but may be easily knocked over.
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
BPM .................... beats per minute
V ......................... volts
min ..................... minutes
or DC ...... direct current
.../min .............. per minute
RPM .................... revolutions per
minute
A ......................... amperes
..................... wear respiratory
protection
..................... wear eye
protection
...................... Class II
Construction
(double insulated)
Ah ....................... amp hours
BATTERIES AND CHARGERS
The battery pack is not fully charged out of the carton.
Before using the battery pack and charger, read the
safety instructions below and then follow charging
procedures outlined. When ordering replacement battery
packs, be sure to include the catalog number and voltage.
READ ALL INSTRUCTIONS
Important Safety Instructions for All
Battery Packs
WARNING: Read all safety warnings, instructions,
and cautionary markings for the battery pack,
charger and product. Failure to follow the
warnings and instructions may result in electric
shock, fire and/or serious injury.
•
Do not charge or use the battery pack in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Inserting or removing the battery
pack from the charger may ignite the dust or fumes.
•
NEVER force the battery pack into the charger. DO
NOT modify the battery pack in any way to fit into a
non-compatible charger as battery pack may rupture
causing serious personal injury. Consult the chart
at the end of this manual for compatibility of batteries
and chargers.
•
Charge the battery packs only in
CRAFTSMAN chargers.
DO NOT splash or immerse in water or other liquids.
•
DO NOT allow water or any liquid to enter battery pack.
•
English
Hz ....................... hertz
W ........................ watts
Wh ...................... watt hours
n o ....................... no load speed
n ......................... rated speed
..................... safety alert symbol
..................... wear hearing
protection
..................... read all
documentation
..................... avoid staring at
light
or AC ........... alternating current
5
Publicidad
Tabla de contenido
