goliath G2 Manual Del Usario página 2

INSTRUCTIONS FOR USE
1 - Loosen the clip (4) from the stand foot, lengthening or shrinking the extendable part of the
machine manually, set the clamp (1) to the desired height and re-attach the foot clip (4).
2 - Loosen the clip (3) of the clamp and set it horizontally, x the clamp medium.
3 - Once we have the clamp at the desired height, horizontal, open and xed we can proceed to
lift the bike manually, when we hold the bike on the clamp we proceed to tighten said clamp (2)
according to frame type.
4 - Already fasten the bike with the clamp, loosen the side loop (3). Look for the necessary angle
according to the inclination of the frame or the work to be performed, x the side loop (3) of the
clamp to keep at the desired angle.
5 - The clamp has no tightening stop (2), the user must determine the pressure he needs
according to the work performed and the type of frame to be fastened.
It is important to know the type of frame to be fastened, as the carbon frames are weaker at
tightening.
*For this type of frame, there is a special clamp (Goliath 360º Carbon), that allows to cover more
frame surface and reduce the e ort per square centimeter. It also has a softer polyurethane
protection and designed to prevent the frame from rolling even with less pressure.
(See our product catalog)
6 - With the raised bike we can rotate it on the axis of the desired clamp.
For this operation we only have to loosen the side loop (3) that secures the clamp.
Once the bike is in the desired position, proceed again to tighten the side loop so that it remains
xed in that position.
7 - Whenever we intend to rotate 180º (or other angle) we must make sure that the clamp has
the necessary pressure (2) on the frame so that it does not roll and can tip sideways.
To return to the starting position, simply loosen the side clip (3) again and hold the bike to its
plane position or the angle you want.
It is very important to make this operation of ipping the bike 180º simple and of little e ort so
that when you hold the bike you look for the most approximate center of gravity.
8 - Once you have nished lifting and want to lower the bike to its starting position, you should
look for the horizontal plane of the clamp before opening it, once opened you can lower the bike
manually.
9 - Goliath Manual is ready to install with all Goliath accessories.
WARNINGS OF DANGER IN THE USE OF THIS STAND:
1- Always place the bicycle on the lift as centered as possible, always looking for the approximate center of gravity.
2- Under no circumstances hold the bicycle by the ends.
3- Always attach the clamp to rigid parts of the frame, avoiding plastic or other weak areas.
4- The stand must not be operated by children, only by adults.
IT IS FORBIDDEN TO WORK UNDER THE LIFTED LOAD WITHOUT SECURING IT WITH APPROPRIATE ADDITIONAL MEANS.
WARNINGS IN CASE OF REPAIR OF THE GOLIATH G2-MANUAL STAND:
1- Only use spare parts from the manufacturer or authorized supplier.
2- The manufacturer is not responsible for any modi cations made without prior authorization from the manufacturer.
3- Only use the GOLIATH G2-MANUAL stand according to the manufacturer's instruction manual.
4- Only carry out maintenance and repairs in accordance with the manufacturer's instruction manual.
5- Repairs and maintenance may only be performed by quali ed personnel.
MAINTENANCE:
1- The stand does not require any speci c maintenance.
2- The only greasing point may be the clamp holder and the clamping clip, which must be lubricated with a little grease, vaseline,
etc.
This greasing process should be done at the user's discretion and although it is not necessary, it does contribute to smoother
movements.
WARNING
THE CLOSING PRESSURE OF THE 360º BASIC CLAMP MUST BE DETERMINED
BY THE USER FOR ITS CORRECT OPERATION.
GOLIATH BIKE WILL NOT BE HELD RESPONSIBLE FOR ANY DAMAGE CAUSED
TO THE FRAME OR ANY PART OF THE BICYCLE DUE TO MISUSE OF THE 360º
BASIC CLAMP, THE USER BEING SOLELY RESPONSIBLE.
IN NO CASE SHOULD THE 360º BASIC CLAMP (G-AC014) BE USED TO HOLD
CARBON FRAMES. FOR THIS WE HAVE THE 360º CARBON CLAMP DESIGNED
EXCLUSIVELY TO EXERT LESS PRESSURE AND NOT DAMAGE CARBON FRAMES.
GOLIATH BIKE manufactured by:
METSISTEM ELDA S.L.
Los Cisnes 12, Elda (Alicante), España
NIF: B54557798
info@goliath-bike.com
WWW.GOLIATH-BIKE.COM