Milwaukee 48-35-1211 Manual Del Operador página 3

SYMBOLOGY
SPECIFICATIONS
Cat. No. ................................................ 48-35-1211
Voltage ...........................................3 V (2xAA) LR6
Reception Angle .............................................. ±40°
Measuring Accuracy Fine ................... ±0.03" @ 33'
Measuring Accuracy Course............... ±0.04" @ 33'
Wavelength Compatibility .................... 510-530 nm
Storage Temp .................................... -4°F to 140°F
Working Range .................................. 15' up to 165'
Receiving Area .................................................... 3"
Ingress Protection............................................ IP54
Center Indication (from top) ........................... 2-1/2"
Auto Shut Off ................................................15 min
NO button press ..........................................3 hrs
Operating Temperature .................... 14°F to 104°F
ASSEMBLY
Changing the Battery
Only use alkaline batteries. Do not use zinc-carbon
batteries. If the laser will not be used for a long
time, remove the batteries as a protection against
corrosion.
Change batteries when the battery indication begins
flashing. To change the batteries:
1. Lift latch to open battery door.
2. Insert two AA batteries according to the +/- polarity
marked in the compartment.
3. Install the battery door securely.
Fuel Gauge
To determine the amount of charge left in the battery,
turn the tool ON. Charge will show in the display: Full,
3/4, 1/2 and Low Battery warning.
*Battery life may vary by brand/age. Replace the
batteries as soon as possible.
OPERATION
To reduce the risk of injury or tem-
WARNING
porary effects on vision, do not
look directly into the laser when it is on.
Use of controls or adjustments or
CAUTION
performance of procedures other
than those specified herein may result in hazard-
ous radiation exposure.
Perform the Accuracy Field Check
NOTICE
procedure immediately upon unboxing
of each new Laser Level Detector and before
exposure to jobsite conditions. See "Accuracy
Field Check" for information.
Volts
Direct Current
Magnets
Read operator's manual
(dependent on laser source)
Turning On/Off
To turn on the laser detector, press the Power But-
ton until the units BEEPS and ICONS and LEDs
Flash.
To turn off the laser detector, press and hold the
power button for more than 2 seconds. Unit will
automatically turn off after 15 minutes with NO but-
tons pressed and NO lasers detected, 3 hours with
laser detected and NO buttons pressed.
Using the Laser Detector
1. Press the Power Button
Back Light ON and Back Light OFF.
2. Press the Volume Button
volume options:
High Volume (Default)
Low Volume
Mute/Silent
3. Press the Accuracy Mode Bottom to toggle
between accuracy options:
Fine (Default)
Coarse
4. Hold the detector so the sensor is facing the laser
source. For best results, ensure the detector is
level or plumb to the ground and the sensor is
perpendicular to the light source.
5. Slowly move the detector up/down or left/ right
in the general area of the projected laser beam.
6. Once the beam is detected, use the Display or LED
indication to align the Center Line of the detector
with the Laser Beam*.
*Use with MILWAUKEE Laser Levels for best results.
To use clamp, align locating posts with the back of
the Detector.
Tighten attachment knob until secure.
Use clamping knob to open/close knobs and attach
to grade rod, 2x4 or similar.
Laser Locating Display and Audible
An arrow will be displayed to indicate which direction
the user must move the Detector in order to align the
Center Line with Laser Beam being detected.
Depending which direction, the speaker will beep at
either 10 hz (fast) or 4 hz (slow) to indicate which
direction to move the detector.
• A solid line will be displayed when the detector
center line is aligned with the laser beam being
detected. The speaker will play a solid tone and
the Green LED will blink.
• When the laser beam being detected is left of the
detector center line, an arrow pointing left will be
displayed. The speaker will beep quickly at 10 hz
and the Red LED will blink.
• When the laser beam being detected is right of the
detector center line, an arrow pointing right will be
displayed. The speaker will beep slowly at 4 hz and
the Blue LED will blink.
• Side LEDs supply the
same color and sound
indicators.
3
to toggle between
to toggle between
Clamp
Indicator