Milwaukee 48-35-1211 Manual Del Operador página 4

Troubleshooting
If the tool does not turn on:
• Ensure batteries are inserted correctly according to
the +/- polarity marked in the compartment.
• Replace batteries that may be at the end of life.
• Ensure the tool's internal temperature is within
specified operating ranges. If stored in excessive
heat or cold, allow at least 2 hours to acclimate to
ambient temperature before turning on the tool.
If problem persists, please contact a MILWAUKEE
service facility for support.
ACCURACY FIELD CHECK
Perform the Accuracy Field Check
NOTICE
procedure immediately upon unboxing
of each new Laser Level Detector and before
exposure to jobsite conditions. See "Accuracy
Field Check" for information. Should any deviation
from listed product accuracy be found, please con-
tact a MILWAUKEE service facility. Failure to do so
could result in rejection of warranty claim.
Influences on Accuracy
Sunlight or other extreme lighting conditions can
inversely impact accuracy. For best results, use
indoors or avoid direct sunlight.
Abusive treatment of the Laser Level Detector, such
as excessive impacts from drop, can lead to devia-
tions in product accuracy.
Therefore, it is recommended to conduct the Field
Check procedure after any impact or before complet-
ing any critical jobs.
For best results, use with MILWAUKEE Lasers.
Horizontal Leveling Accuracy
1. Set up compatible laser 33' from flat wall. Turn on
lasers horizontal beam.
2. Ensure the laser source is self leveled and per-
pendicular to wall.
3. Place detector flat on wall directly in front of the
laser source and slightly below the projected
laser line.
4. Keeping the detector bottom parallel with the
ground, raise detector until down arrow appears.
5. Lower detector until center line appears.
6. Mark a line on the wall – Point I.
7. Continue to lower detector until up arrow appears.
8. Raise detector until center line appears.
9. Mark a line on the wall – Point II.
10. Measure the distance between Point I and Point
II – divide by 2.
Point I
Point I
d
Point II
Point II
MAINTENANCE
To reduce the risk of injury, always
WARNING
remove the battery before perform-
ing any maintenance. Never disassemble the tool.
Maintain Laser Detector
Maintain tools. If damaged, have the tool repaired
before use. Accidents may be caused by poorly
maintained tools.
To reduce the risk of personal in-
WARNING
jury and damage, never immerse
your tool in liquid or allow a liquid to flow inside
them.
Keep tool housing clean, dry and free of oil or grease.
Use only mild soap and a damp cloth to clean the
tool since certain cleaning agents and solvents are
harmful to plastics and other insulated parts. Some
of these include gasoline, turpentine, lacquer thin-
ner, paint thinner, chlorinated cleaning solvents,
ammonia and household detergents containing am-
monia. Never use flammable or combustible solvents
around tools.
Cleaning the Sensor Window
Blow off loose particles with clean compressed air.
Carefully wipe the surface with a cotton swab moist-
ened with water.
This tool has limited serviceable parts. Do not open
housing or disassemble tool. For repairs, return the
tool, battery pack and charger to the nearest autho-
rized service center.
ACCESSORIES
Use tools only with specifically
WARNING
designated accessories. Use of any
other accessories may create risk of injury.
SERVICE - UNITED STATES
1-800-SAWDUST
Monday-Friday, 7:00 AM - 6:30 PM CST
www.milwaukeetool.com
or visit
Contact Corporate After Sales Service Technical
Support with technical, service/repair, or warranty
questions.
Email: metproductsupport@milwaukeetool.com
B e c o m e a H e a v y D u t y C l u b M e m b e r a t
www.milwaukeetool.com to receive important
notifications regarding your tool purchases.
SERVICE - CANADA
Milwaukee Tool (Canada) Ltd
1.800.268.4015
Monday-Friday, 7:00 AM - 4:30 PM CST
or visit www.milwaukeetool.ca
LIMITED WARRANTY USA & CANADA
Every MILWAUKEE power tool* (see exceptions below) is warranted
to the original purchaser only to be free from defects in material and
workmanship. Subject to certain exceptions, MILWAUKEE will repair or
replace any part on an electric power tool which, after examination, is
determined by MILWAUKEE to be defective in material or workmanship
for a period of five (5) years** after the date of purchase unless otherwise
noted. Return of the power tool to a MILWAUKEE factory Service Center
location or MILWAUKEE Authorized Service Station, freight prepaid and
insured, is required. A copy of the proof of purchase should be included
with the return product. This warranty does not apply to damage that
MILWAUKEE determines to be from repairs made or attempted by
anyone other than MILWAUKEE authorized personnel, misuse, altera-
tions, abuse, normal wear and tear, lack of maintenance, or accidents.
Normal Wear: Many power tools need periodic parts replacement and
4
Cleaning
Repairs
(1.800.729.3878)