EarthWise PW15003 Manual Del Operario página 3

This pressure washer is equipped with a stop device which will sense
when the trigger of the gun is released causing the pressure washer to
stop.
WARNING: If the pressure washer fails to stop when the trigger of the
gun is released, disconnect from the power source. DO NOT USE THE
PRESSURE WASHER. Call our customer service help line at
1-800-313-5111 for assistance.
This pressure washer is also equipped with a thermal safety switch that
will automatically shut off the motor in the event the motor overheats.
Should that occur, after the motor has cooled down, reset the switch and
you can resume normal operation again..
WARNING: To reduce the risk of electrocution, keep all connections
dry and off the ground. Do not touch plug with wet hands.
WARNING: Test GFCI before each use. DO NOT use pressure washer
if following test fails.
GFCI Test Procedures:
-Plug GFCI into power receptacle. Indicator light should be illuminated.
-Press Test button. Light should turn off.
-Press Reset button for use. Indicator light should be illuminated.
DO NOT USE if above test fails and call our customer service help line
at 1-800-313-5111 for assistance.
NOTE: The GFCI must be reset each time the pressure washer is con-
nected to an electrical outlet. Reset by simply pushing the reset button on
the GFCI power plug.
If an extension cord is used, the plug and socket must remain away from
all water and moisture.
WARNING: Risk of shock. Do not tough the plug or outlet with wet
hands.
The narrow pinpoint stream is very powerful. It is not recommended for
use on painted surfaces, wood surfaces or items attached with an adhe-
sive backing.
The optimum angle for spraying water against a cleaning surface is 45
degrees.
To minimize the amount of water getting into the pressure washer, the
unit should be placed as far as possible from the cleaning site during
operation.
WINTERIZING AND LONG-TERM STORAGE
 Run the pressure washer in low pressure until all of the soap is drained
from the detergent tank.
 Pour clear water into the tank and run it through on low pressure as
though it were detergent.
 Disconnect all water connections.
 Turn on the machine for a few seconds to expel any water remaining in
the pump and turn off immediately.
 Do not allow the high pressure hose to become kinked.
 Store the equipment and accessories in an area where they will not
freeze.
Do not store near a furnace or other source of heat as it may dry out the
pump seals.
OPERATING
QUICK START GUIDE
 Carefully remove the pressure washer and all accessories from the
carton.
 Inspect for damage and verify no parts are missing.
PARTS LIST:
Pressure Washer
Operator's Manual
Nozzle Cleaning Pin
Hang Hooks (2)
Gun Handle
Spray Lance
High Pressure Hose Assembly
Soap Bottle
NOTE: Any part that is damaged should be properly repaired or replaced.
Call our customer service help line at 1-800-313-5111 for assistance.
 Install hang hooks.
 Connect high pressure hose to gun handle.
 Connect a garden hose to the water faucet. (The garden hose is not
included.) NOTE: Do not turn on the water until after you have
connected the garden hose to the water inlet connector.
OPERATING INSTRUCTIONS
1) Connect the high pressure hose to the water outlet on the back of the
unit.
2) Insert the spray lance into the gun handle. NOTE: Make sure it is
locked into place.
WARNING: If the attachment is not securely locked into place, it could
be ejected when operation the gun under high pressure.
3) Securely attach garden hose to the water inlet fitting (located on the
front of the unit).
4) Turn on the water supply.
5) Plug GFCI into power receptacle. Press reset button. Indicator should
be "ON". Press test button. Indicator should be "OFF". Press reset
button for use. Do not use if this test fails.
6) Squeeze and hold the trigger until water flow is steady, then release
the trigger.
7) Turn on the pressure washer. Squeeze the trigger to start the motor.
The motor only starts if the trigger of the gun is pulled and shuts off
when the trigger is released. (If taking a break for longer than three
(3) minutes, release the trigger and switch off the unit.)
USING THE SOAP BOTTLE:

Pour detergent into the soap bottle. Attach the dispensing connector
firmly to the bottle.

Connect soap bottle to spray gun securely.

Engage gun trigger, discharge water and connect pressure washer to
power supply.

Liquid detergent will be drawn slowly into the spray, mixed with
water. (Spray will generally remain clear during the soap dispensing
function).

Use a cloth to scrub surface after spraying detergent.

After scrubbing, rinse with high pressure wash.
After the job is completed, to disconnect the unit, turn off the water
source and squeeze the trigger of the gun to release the water pressure.
You may now disconnect the garden hose from the water inlet nut on the
unit.
WARNING: When leaving unattended, push the trigger lock button
firmly through the gun handle to lock the trigger.
WARNING: Make sure to point the gun in a safe direction when starting
the pressure washer. Serious injury could result if pointed at face, feet,
animal or other people when starting pressure washer.
WARNING: Carefully read the operator's manual before using the
pressure washer. Always store in a location where the temperature will
not fall below freezing. Freeze damage is not covered by the warranty.
WARNING: When you are finished using the pressure washer, switch
off the unit and unplug the cored from the electrical outlet.
3