Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
NOTE: Before starting installation, read all the steps
of these instructions.
Use the illustration beside to identify your kitchen
cabinet type.
This manual covers 2 kinds of installation: the standard
(without EZ1 brackets) and the EZ1 one-person
installation system (using included template and
brackets). For the standard installation, go to page 14.
EZ1 installation is designed for use with kitchen cabinets that have the same width designation as the range
hood width. If the cabinet is greater than 1/2" wider than the range hood width, please use the standard
installation method.
1. Use the proper template for vertical OR horizontal
disharge (included) for placement of ductwork and
electrical cutout in cabinet or wall. For a non-ducted
installation, DO NOT cut a duct access hole, only cut
the hole for electrical wiring. If replacing a hood and
plan to use the existing duct and electrical, steps 2 to
5 may not be necessary. If so, skip to step 6.
2. Measure and mark the hood center line on cabinet
bottom.
4. Drill a 1/8" dia. pilot hole for house wiring,
at B location on template.
5. Use a sharp pencil or 1/8" drill bit to mark the
locations for the appropriate duct access holes
(16 locations for 7" round duct, or 4 corner locations
for rectangular duct). Remove the template.
PREPARE THE HOOD LOCATION
EZ1 One-person installation system
CABINET FRONT
Use this template for marking; do not attempt to cut out the ducting hole through it.
M
NOTE: These cutouts are clearance holes; they do not need to be the exact size of ducting.
ARK WHERE INDICATED
Utiliser ce gabarit pour marquer vos repères; ne pas tenter de découper
FOR THE APPROPRIATE SIZE DUCT OPENING
le trou pour le conduit à travers le gabarit.
7" R
D
OR
NOTE : Les découpes incluent le jeu nécessaire à l'installation; elles ne doivent pas
OUND
UCTING
être du format exact des conduits.
Use esta plantilla para crear marcados; no trate de cortar el
agujero del conducto a través de la plantilla.
NOTA: To be translated in Spanish.
M
ARQUER LES REPÈRES AUX ENDROITS INDIQUÉS SELON
LE FORMAT DE CONDUIT UTILISÉ
C
Bend template along graduated
OU
scale when installing to framed
C
ONDUIT ROND DE
7
PO
cabinet.
Pour une installation sous une
armoire à fond en retrait, utiliser les
lignes pour mesurer l'épaisseur du
décalage causé par le mur de
l'armoire et plier le gabarit en
T
ITLE TO BE TRANSLATED IN
S
PANISH
8"
conséquence.
C L
To be translated in Spanish.
C
O
ONDUCTO REDONDO
7
.
DE
PULG
7½"
V RTICAL EX
VERTICAL EXHAUST
A
A
A
10½"
4¼"
14½"
C
Place this edge against back wall
Appuyer ce bord au mur arrière
Apoyar este borde contra la pared de atrás
C
F
OLD TEMPLATE ALONG GRADUATED
SCALE WHEN INSTALLING TO FRAMED
P
.
CABINET
CENTER LINE
FRAMED CABINET
3. Align the center line on template with the hood
center line marked on the bottom of the cabinet,
placing the edge (where indicated) of the template
against back wall. When using with framed cabinet
for vertical exhaust installation, fold over rear edge
of template equal to the depth of the cabinet frame
at the wall (use graduations on template, C locations
on template). Tape the template in place.
NOTE: When facing the installation, A and B (on
template) must be at right.
CABINET FRONT
Use this template for marking; do not attempt to cut out the ducting hole through it.
NOTE: These cutouts are clearance holes; they do not need to be the exact size of ducting.
Utiliser ce gabarit pour marquer vos repères; ne pas tenter de découper
le trou pour le conduit à travers le gabarit.
R
D
ECTANGULAR
UCTING
NOTE : Les découpes incluent le jeu nécessaire à l'installation; elles ne doivent pas
= 3¼" x 10"
être du format exact des conduits.
= 3¼" x 14"
Use esta plantilla para crear marcados; no trate de cortar el
agujero del conducto a través de la plantilla.
NOTA: To be translated in Spanish.
C
Bend template along graduated
C
ONDUIT RECTANGULAIRE
scale when installing to framed
= 3¼ po x 10 po
cabinet.
Pour une installation sous une
= 3¼ po x 14 po
armoire à fond en retrait, utiliser les
lignes pour mesurer l'épaisseur du
décalage causé par le mur de
l'armoire et plier le gabarit en
conséquence.
C
To be translated in Spanish.
ONDUCTO RECTANGULAR
= 3¼ pulg. x 10 pulg.
= 3¼ pulg. x 14 pulg.
Electrical access hole center
A = single blower hood
B = double blower hood
Centre du trou pour fil
S
d'alimentation électrique
A = hotte ventilateur simple
B = hotte ventilateur double
To be translated in Spanish
Electrical access hole center
A = single blower hood
B = double blower hood
A
B
C
CENTER LINE
HORIZONTAL
EXHAUST DUCTING
A
Place this edge against
cabinet bottom.
Appuyer ce bord contre le bas
Electrical access hole center
de l'armoire.
A = single blower hood
Apoyar este borde contra
B = double blower hood
la base del armario.
Centre du trou pour fil
d'alimentation électrique
A = hotte ventilateur simple
B = hotte ventilateur double
C L
To be translated in Spanish
Electrical access hole center
A = single blower hood
B = double blower hood
M
M
ARK WHERE INDICATED
ARQUER LES REPÈRES AUX ENDROITS INDIQUÉS SELON
Use this template for marking; do not attempt to cut out the ducting hole through it.
FOR THE APPROPRIATE SIZE DUCT OPENING
LE FORMAT DE CONDUIT UTILISÉ
NOTE: These cutouts are clearance holes; they do not need to be the exact size of ducting.
R
ECTANGULAR
D
UCTING
C
ONDUIT RECTANGULAIRE
Utiliser ce gabarit pour marquer vos repères; ne pas tenter de découper
= 3¼" x 10"
= 3¼ po x 10 po
le trou pour le conduit à travers le gabarit.
= 3¼" x 14"
= 3¼ po x 14 po
NOTE : Les découpes incluent le jeu nécessaire à l'installation; elles ne doivent pas
être du format exact des conduits.
T
S
ITLE TO BE TRANSLATED IN
PANISH
Use esta plantilla para crear marcados; no trate de cortar el
agujero del conducto a través de la plantilla.
C
ONDUCTO RECTANGULAR
NOTA: To be translated in Spanish.
= 3¼ pulg. x 10 pulg.
= 3¼ pulg. x 14 pulg.
T T
6. Draw the border for the exhaust ducting by linking its
marks (16 for round duct and 4 for rectangular duct),
then cut the opening in the cabinet bottom (vertical
exhaust) or in the wall (horizontal exhaust). Drill the
house wiring hole by using a 1½" hole saw centered
with the pilot hole previously made in 4.
11
FRAMELESS CABINET
VERTICAL
EXHAUST DUCTING
M
ARK WHERE INDICATED
FOR THE APPROPRIATE SIZE DUCT OPENING
7" R
D
OR
R
D
OUND
UCTING
ECTANGULAR
UCTING
= 3¼" x 10"
= 3¼" x 14"
M
ARQUER LES REPÈRES AUX ENDROITS INDIQUÉS SELON
LE FORMAT DE CONDUIT UTILISÉ
OU
C
ONDUIT ROND DE
7
PO
C
ONDUIT RECTANGULAIRE
= 3¼ po x 10 po
= 3¼ po x 14 po
T
ITLE TO BE TRANSLATED IN
S
PANISH
8"
C L
C
O
C
ONDUCTO REDONDO
ONDUCTO RECTANGULAR
7
.
= 3¼ pulg. x 10 pulg.
DE
PULG
= 3¼ pulg. x 14 pulg.
7½"
Electrical access hole center
A = single blower hood
B = double blower hood
Centre du trou pour fil
V RTICAL EX
VERTICAL EXHAUST
A
A
A
S
d'alimentation électrique
A = hotte ventilateur simple
B = hotte ventilateur double
10½"
To be translated in Spanish
4¼"
Electrical access hole center
A = single blower hood
B = double blower hood
14½"
A
B
C
C
ELECTRICAL
B
ACCESS HOLE
LOCATION (B)
(
)
IN CABINET BOTTOM
B
B
ess hole center
wer hood
wer hood
ELECTRICAL
ACCESS HOLE
LOCATION (B)
(
)
IN WALL
Publicidad
Capítulos
Tabla de contenido
