Battery Safety; Assembly - Husqvarna X-COM R HP310-1, X-COM R HP310-2 Manual De Usuario

General safety
WARNING: Read the warning instructions
that follow before you use the product.
• Use and save these instructions.
• For optimal fit and function, make sure that you have
selected the correct product for your use.
• Do not change or remove parts on the product. Only
do changes that are given in this operator's manual.
• The noise attenuation of the product will be severely
impaired if you do not follow the instructions in this
operator's manual. Ear-muffs, and in particular
cushions, may deteriorate with use and should be
examined at frequent intervals for cracking and
leakage, for example.
• This product may be adversely affected by certain
chemical substances. Further information should be
sought from the manufacturer. Keep away from
aggressive substances and clean the product
regularly. Use a cloth with water and soap. Do not
wash or put fully into water.
• All service and repair work must be done by an
approved service workshop. Only use Husqvarna
original spare parts.
• Never use the ear-muffs longer than 10 years from
the manufacturing date stated on the packaging.
Safety instructions for operation
• The wearer should ensure that the ear-muffs are
worn at all times in noisy environments.
• Be more careful and listen for warning signals when
you use the product. The noise from warning signals
can be decreased when you use the product.
• The audibility of warning signals at specific
workplace may be impaired while using the
entertainment facility.
• Make sure that the product is not hit during
transportation and use.
• Only use the product between temperatures -20°C
and +55°C. If you use the product in other
Introduction
WARNING: Move your hair to the side
before you assemble the product. Make sure
that the sealing rings are tight against your
head and around your ears before you
operate the product.
To put on the earmuffs with headband
1. Put the headband across the top of your head.
2. Move the earmuffs up or down to adjust the height.
(Fig. 6)
579 - 005 - 05.07.2019
temperatures, this can cause damage to the
electronics, battery and mechanical parts. This
model of earmuffs has satisfied the requirements of
the drop test at −20 °C.
• Make sure that you know how to use the product
before use. Speak to your servicing dealer if there is
damage on the product. Do not open the casing!
• The fitting of hygiene covers to the cushions, may
affect the acoustic performance of the ear-muffs.
Always use original accessories.
• Do not push the earmuffs against the helmet shell. If
you do that, it can cause cracks around the side of
the helmet.
(Fig. 5)
• Do not put the product in storage at temperatures
above +55°C, for example on a dashboard. Do not
put the product in storage at temperatures below
-20°C.
• The wearer should ensure that the ear-muffs are
fitted, adjusted and maintained in accordance with
this operator's manual.
• The ear-muff is provided with safety-related audio
input. The user should check correct operation
before use. If distortion or failure is detected, the
user should refer to the manufacturer's advice for
maintenance.

Battery safety

• The product contains battery and electrical
components that may cause ignition in flammable or
explosive atmospheres. Do not use in environments
where sparks may cause a fire or explosion.
• Use only original charger cable. Use of any other
cable can damage the product. The original charger
cable is identified by the label with text "ORIGINAL
CHARGER CABLE FOR HP310". Make sure that the
charger used, fulfill country specific regulations. Do
not leave the ear-muffs to charge unattended.
• Only charge the product within temperature range
0°C to +40°C. Charging outside temperature range
can damage the electronics and battery.

Assembly

To assemble the earmuffs to a helmet
1. Remove the transport protection from the helmet
attachment.
2. Assemble the helmet attachment on the helmet fork.
(Fig. 7)
Note: Refer to
more information about which helmet attachment is
applicable to your helmet.
3. Move the earmuffs to the lowest position.
Approved helmets on page 11 for
7