Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Flash Patterns:
POWER-UP RESET:
After installing the system it is best to do a POWER-UP RESET the first time
to ensure all heads are in sync.
Touch BLUE wires to +V (RED wire) while applying power.
Release BLUE wires. All heads will reset to Pattern #2.
If you have installed a pattern select push-button, press and hold
pattern select while turning power switch ON.
To select a flash pattern, touch BLUE to +V or press pattern select switch to
increment the flash pattern. The heads will remember the selected pattern
even if power is removed.
STANDARD PATTERNS:
The 3510 ships with sixteen patterns enabled. Standard patterns 1 through
8 are compatible with older BULL LED™ and HIDE-A-LED™ products.
CYCLE PATTERNS:
You may revert to patterns 1 through 8 by following this procedure:
1) Touch BLUE wires to +V (RED wire) while applying power.
If you have installed a pattern select push-button, press and hold
pattern select while turning power switch ON.
2) Hold BLUE wires on +V for 5 SECONDS (heads will not be flashing
during this time). After 5 SECONDS the heads will flash once or twice to
indicate the flash pattern list that has been selected:
ONE FLASH = Standard Patterns only.
TWO FLASHES = Standard + Cycle Patterns.
3) Remove the BLUE wires from +V (or release push-button).
You may switch the pattern set at any time as many times as you wish. All
heads will remember the pattern set that was selected even when power
is removed.
#
Pattern:
Frequency:
1
Quad Flash
Double Flash
2
3
Triple Flash
4
DeciBlast
5
Single Flash
Mega Flash
6
7
Triple+Burst
8
Steady On
Cycle All
9
10
Double-
Triple+Burst
Cycle Classic
11
Quad-Mega
12
13
Single-Quad
DeciBlast-Quad
14
Single-Triple-
15
DeciBlast
16
Mega-
Triple+Burst
920-9140-00 Rev. D
STANDARD PATTERNS
Description:
1.25 Hz
75 Quad Flashes Per Minute
1.25 Hz
75 Double Flashes Per Minute
1.53 Hz
92.3 Triple Flashes Per Minute
1.42 Hz
85.5 Deci Flashes Per Minute
1.25 Hz
75 Single Flashes Per Minute
1.90 Hz
114 Single Flashes Per Minute
1.37 Hz
82.5 Triple+Burst Flashes Per Minute
Steady on. Split Color = Fast Mega
CYCLE PATTERNS
Cycle through patterns 1 to 7
2 Double, 2 Triple+Burst cycle
1 Double, 1 Quad, 4 Mega cycle
3 Quad, 5 Mega cycle
2 Single, 2 Quad cycle
2 DeciBlast, 2 Quad cycle
2 Single, 2 Triple, 2 DeciBlast cycle
1 Mega, 1 Triple+Burst cycle
Troubleshooting:
HEAD NOT FLASHING:
Check the RED and BLACK wires for a reversed connection. (Reverse
connection will not damage the unit). Check RED and BLACK wires for either a
bad splice or a corroded ground connection.
HEADS NOT SYNCHRONIZING:
Check for a short circuit on the BLUE wire to either +V or GROUND.
Saltwater on the wire connections will short circuit the sync signal on the BLUE
wire. Check for non-functional heads in the system. If any one of the heads has
a bad GROUND connection it can cause the sync signal to become corrupted.
If any one of the heads has it's RED and BLACK wires reverse connected it will
corrupt the sync signal.
FLASH PATTERN CHANGING:
If the flash pattern changes on it's own there may be an intermittent short
between the BLUE wire and +V. Check for water in the wiring connections.
If any one of the heads in the system has an intermittent GROUND connection
it can also cause the flash pattern to change.
SAE
CA T13
J 595
Class B
Class 1
x
x
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Page 3 of 12
Publicidad
Tabla de contenido
