Kohler Sterling SP2270 Serie Instrucciones De Instalación Y Cuidado

USA/Canada: 1-800-STERLING (1-800-783-7546)
México: 001-877-680-1310 SterlingPlumbing.com
WARNING: Risk of serious injury. Damage prior to installation can
result in glass shattering. Inspect the glass and all parts for damage
before installation.
WARNING: Risk of serious injury. Improper installation can result
in glass shattering. Follow all installation instructions.
WARNING: Risk of serious injury. Do not cut tempered glass.
Tempered glass will shatter if cut.
WARNING: Risk of serious injury. Shower door and side panels
can shatter. Regularly inspect the glass and all parts for damage,
missing, or loose parts.
WARNING: Risk of serious injury. Always wear safety glasses
while cutting and drilling.
NOTICE: Do not touch the edges of the tempered glass with tools or any
other hard objects. Do not set the unframed tempered glass directly on the
floor or any hard surface.
IMPORTANT! Leave this manual for the end user.
Read these instructions before installing or using this product.
IMPORTANT! Do not cut the top track the same length as the bottom track.
Walls must be within 3/8" (10 mm) of plumb.
Cover the drain with tape to avoid loss of small parts.
Follow the silicone sealant manufacturer's instructions for application and
curing time.
To watch this installation online; visit the product page at
www.sterlingplumbing.com.
For care and cleaning and other information; visit
www.sterlingplumbing.com/care-and-cleaning.
Mark the location of the wall jambs. The front
1
edge should be 3/4" (19 mm) from the front edge
of the threshold.
3/4"
3/4"
(19 mm)
(19 mm)
Apply a bead of silicone sealant to the groove
6
along the entire wall jamb.
x2
Silicone Sealant
Front Edge
1187937-2-C
Required Tools
Tin Snips Assorted Drill Bits
100% Silicone Sealant Masking Tape
Move the wall jambs into place and check the fit.
2
When needed, snip and file the bottom edges of
the wall jambs for a snug fit.
Front
Front
Edge
Edge
Move a wall jamb into place with the sealant
7
groove against the wall, toward the outside of
the shower. Secure with three screws. Repeat for
other side.
Front
Edge
Screws
#8-18 x
1-3/4"
Parts Identifi cation
1080993**
Hardware Pack
919918
919919
919932
919933
1077762
919934
Anchor
Bridge Member (Includes Seal 521307)
1049018-T (Black)
1049018-D (Silver)
1048208-A
1049018-L (Brass)
Screw
Screw
681200
Magnet
681301
Magnet
681501 (Silver)
681511 (Brass)
681544 (Nickel)
681545 (Matte Silver)
681546 (Deep Bronze)
Wall Jamb
Side Panel*
682001 (Silver)
682011 (Brass)
682038 (Nickel)
682039 (Matte Silver)
682040 (Deep Bronze)
Column
684101 (Silver)
684110 (Brass)
1031659-C
684130 (Nickel)
Screw
684131 (Matte Silver)
684132 (Deep Bronze)
Strike Post (Includes Magnet 681200)
Align the front edge of the wall jambs with the
3
marks. Plumb the wall jambs. Mark the front
edges of the wall jambs and the wall jamb holes.
x2
Pencil
Front
Front
Edge Edge
Level
Wall Jamb
Carefully lift the side panels onto the shower
8
ledge. Align the expander jamb on the panel with
the wall jamb.
Expander Jamb
x2
Wall Jamb
1
Installation and Care Instructions
(Silver)
(Brass)
1088416
(Nickel)
Pivot Pin
(Matte Silver)
1088417
(Deep Bronze)
Bushing
1049018-S (Black)
1049018-J (Silver)
1049018-K (Brass)
Screw
521311
Seal
Door Panel*
(Includes Magnet 681301)
Series
Number Label
1088771
Panel Cushion
1031659-C
Screw
1052892-A
Washer
1088416
Pivot Pin
1088418
1088417
Plug
Bushing
Remove the wall jambs. Drill 5/16" holes at each
4
mark and insert an anchor in each hole.
x2
5/16" Drill
Bit
3
2
1
Use a screwdriver to tighten or loosen the
9
adjustment blocks until they firmly and evenly
contact the wall frame.
Expander
Jamb
Adjustment Block
SP2270 Series Neo-Angle Shower Doors
*Call Customer Care Center to order replacement parts.
**Finish/color code must be specifi ed when ordering.
Retain this document for future servicing.
Record model number from box for reference.
Model Number:______________
1031813
Adjustment Block
521307
Seal
681501 (Silver)
681511 (Brass)
681544 (Nickel)
681545 (Matte Silver)
681546 (Deep Bronze)
Wall Jamb
Side Panel*
682001 (Silver)
682011 (Brass)
682038 (Nickel)
682039 (Matte Silver)
(Deep Bronze)
682040
Column
684001 (Silver)
684010 (Brass)
684030 (Nickel)
684031 (Matte Silver)
684032 (Deep Bronze)
Flange (Includes Seal 521311)
521307
Seal
Slide an adjustment block onto each end of the
5
wall jambs, positioned over the first hole. Secure
in place with tape. Loosen the adjustment in each
adjustment block until it extends 1/2" (13 mm).
1/2"
(13 mm)
Tape
Wall Jamb
Secure the wall panels in place with two screws.
10
Screw
x4
#8 x 3-1/2"
Screw