Instructions - NuWave PIC Gold El Manual Del Propietario

INSTRUCTIONS

To Start Cooking
There are several ways to
begin cooking with your
PIC Gold.
Press "Start". Default is
1.
375°F (191°C) for 1 hour
of cooking.
Set temperature and
2.
press "Start". Default is
for 1 hour of cooking.
Set cooking time and
3.
press "Start". Default
temperature is 375°F
(191°C).
Set temperature and time,
4.
then press "Start".
The PIC Gold will
•
automatically stop
cooking once time has
expired and the PIC will
beep.
The display will always
•
show current temperature
during the cooking cycle.
To display time lapse,
•
press "Time" and a
countdown will appear,
marking the duration
before the cycle or stage
is complete.
Setting Temperature
This appliance is pre-
set to cook on Med/High
(375°F/191°C).
To reset, press the
1.
desired temperature
on the control panel
then press "Start". The
temperature range will
10 10
instructions
appear on the display
panel.
To raise or lower the
2.
temperature in 10-degree
(5 - 6 Celsius) increments,
press "+" or "-" until the
desired temperature is
displayed.
Refer to Panel Display Chart
for preset temperatures.
NOTE: Displayed temperature
represents the center
temperature of 1.5L of oil
in the NuWave 3.5-quart
(4L) Stainless Steel Pot.
Thermometer location was
tested at the origin (middle)
of the NuWave 3.5-quart (4L)
Stainless Steel Pot at an
equidistant length between
the pot base and the top of
the oil.
ºF to ºC
The PIC Gold's LED screen
is defaulted to display
cooking temperature in
Fahrenheit (F).
To switch the display to
1.
Celsius (C), press "Prog",
followed by "-". Press
"-" again to convert to
Celsius.
To return to Fahrenheit,
2.
press "-" once more.
To close out of the F/C
3.
conversion option, press
the "Pause/Clear" button
until a "0" appears on the
PIC's screen.
Setting Cooking Time
Press "Time". A "0" will
1.
flash in the far right corner
of the display panel.
Press "+" until the
2.
desired amount of time is
reached.
Example 1: To program 5
minutes, press "Time" once,
then press "+" until "00:05" is
displayed. Press "Start".
Example 2: For 20 minutes,
press "Time" twice, then press
"+" until "00:20" is displayed.
Press "Start".
Example 3: For 2 hours and
30 minutes, press "Time"
twice, then press "+" until you
reach "00:30", then press
"Time" again. Press "+" until
"02:30" is displayed, then
press "Start".
The blinking "0" indicates
•
the digit you can adjust.
The maximum time is 99
hours and 60 minutes.
The display shows hours
•
and minutes, but not
seconds.
Pause/Clear Function
To interrupt cooking time,
1.
press "Pause/Clear"
once. This will pause
the NuWave PIC Gold
regardless of cooking
stage.
The temperature will
•
remain listed in the
display panel, but the
"F" will be blinking.
To resume, press "Start".
2.
NOTE: To clear the cooking
mode or display while the
PIC Gold is in operation,
press the "Pause/Clear"
button twice. The screen will
be fully cleared and "0" will
appear.
Programming Function
(Stage Cooking)
Press "Prog". "Pro" will
1.
appear in the display
panel.
Input the desired set
2.
temperature, ranging from
"Low" to "Max/Sear". To
increase or decrease the
temperature, press "-" or
"+".
Press "Time". "00:00" will
3.
be displayed, then press
"-" or "+" until the desired
time is reached. See
"Setting Cooking Time"
for entering minutes and
hours.
To add additional stages,
•
repeat steps 1 and 2
then press "Start" to
begin the program.
You may program up
to 10 stages (delay is
considered a stage).
To change any part
•
of the program, press
"Pause/Clear" twice to
start over.
Example: Boil for 5 minutes
before reducing to a simmer
for 20 minutes:
Press "Prog". Press "Max/
11 11
nuwavenow.com nuwavenow.com