AirKing 4C523K Manual De Instrucciones De Operación Y Partes

MODELO 4C523K/9154K
ENSAMBLAJE
(Ilustración para Ensamble - Pagina 1)
1. Alinea la REJILLA TRASERA con el pasador localizado en la TAPA
DE PLASTICO DEL MOTOR. Dejando los dos agujeros del centro asi
abajo.
2. Asiente la REJILLA y sujetela con la TUERCA DE PLÁSTICO.
3. Para evitar lastimar el HELICE, instalela empujando firmemente en el
a) Jalé el boton de oscilacion asi
1
a
arriba para desenganchar el
mecanismo de oscilacion.
b) Usé un objecto como un mango
Centro
EJE
de un destornillador y
gentilmente pegé un golpecito
a la parte delantera de la helice.
2
b
No golpear el eje de la helice
asi adentro del motor.
LIGERAMENTE
c) Delé vuelta a la helice con la
mano. Si la helice no davuelta
libremente, sigá el paso
posterior hasta que la helice
3
c
gire libre.
PRECAUCION: De ninguna
manera prenda su ventilador sin
las revillas y asegurese que
ambas esten bien aseguradas.
11
27
14-
Rev. F 9/00
centro hacia el EJE del MOTOR.
4. Coloque el GANCHO en la REJILLA DELANTERA sobre el alambre
central superior en la REJILLA TRASERA.
5. Torciendo suavemente quitar del sujetador los GANCHOS de la
REJILLA y colocarlos uniformemente alrededor del ventilador. Fijar
los GANCHOS en la REJILLA. Hacer que la cola del gancho agarre un
alambre redondo de la REJILLA TRASERA. Hacer que el cuerpo del
gancho agarre los bordes planos de ambas rejillas. (Figura a y b
pagina 1)
OPERACIÓN
UP
1. VELOCIDAD: Las velocidades se controlan mediante el conjuntor
ARRIBA
rotatorio localizado en la base del ventilador.
2. OSCILACIÓN: Para hacer oscilar el ventilador, oprima el botón que se
encuentra sobre la cubierta del motor. Para que el ventilador deje de
TAP
oscilar, tire del botón hacia afuera.
HUB
GOLPEAR
3. AJUSTE DEL ÁNGULO: Se puede cambiar el ángulo del conjunto
EJE
superior del ventilador, aflojando primero el tornillo de elevación. Coloque
el conjunto superior en el ángulo deseado y fíjelo en posición volviendo
a apretar el tornillo de elevación.
LISTA DE REPUESTOS
GIRAR
SPIN
Ref. No. de Parte Descripción
1 2050009AW Cordón Eléctrico
2 2096045 Rejilla Delantera
3 2010004 Hélice
4 2010350 Tuerca de Plástico
5 2096050 Rejilla Trasera
6 2030056G Motor
7 2010619 Cubierta del Motor
8 2010119 Botón de Oscilación
22
10 2010279 Enlace
11 2090068 Tornillo #6 x 1/2" LH/H.W.H.
12 2010260 Cuello
13 2091133 Tuerca Hexagonal de 1/4 x 20
14 2090529 Tuerca Para Alambre
15 2090199 Tornillo Phillips de 1/4 - 20 x 1"
PPH Tornillo de Elevación
16 2010104 Botón del Interruptor
17 2065412 Ornamento de la Base
18 2010524 Base
19 2057065 Conjuntor Rotatorio
20 2010281 Placa Inferior
21 2010403A Pata de Caucho (4 utilizadas)
22 2090038 Tornillo Phillips de Cabeza
Reforzada #8 x 9/16 PPH
23 2010354 Sujetador de Rejilla
24 2066506G Accesorio del Botón del
Interruptor
25 2010241A Ornamento del Rejilla
26 2070024G Ojo de Buey (AirKing)
27 2090073 Tornillo #6 x 1/2" AB
4
OPERATING INSTRUCTIONS & PARTS MANUAL
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED.
PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH
INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE!
OSCILLATION CONTROL
MOTOR
REAR GRILL
Cant.
1
1
1
1
1
SWITCH KNOB
1
ELEVATION
GRILL CLIP
SCREW
1 HOLDER
1
1
1
1
1
1
DESCRIPTION
The AirKing 9" (22.9 cm) oscillating fan features whisper-quiet perfor-
1
mance with a 3-paddle fan blade. The fan has a permanently lubricated
1
motor with a 6 ft (1.8 m) 18/3 cord set.
1
SPECIFICATIONS
1
Motor ................................................ 120V, 60 Hz
Blade diameter ................................ 9" (22.9 cm)
1
Speeds ............................................. 2
Control ............................................. Rotary Switch
1
Air flow distribution .......................... 90°
4
Approvals ......................................... UL Listed. Close mesh fan
2
MODEL 4C523K/9154K
5
SPEED HIGH
CFM 1205
1 3
M /s .57
RPM 2175
1
Amps .55
1
Watts 32
dB A 41
1
2084020A Rev. F 9/00
R
9 INCH OSCILLATING FAN
MODEL 4C523K/9154K
READ AND SAVE THESE INSTRUCTIONS
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.
GENERAL SAFETY INFORMATION
1. Make certain that the power source conforms to the electrical require-
ments of the fan.
PLASTIC
2. The power cord is equipped with a three-prong grounded plug that must
NUT
BLADE be inserted into a matching receptacle. Under no circumstances must
HOOK the grounding prong be cut off the plug. Where a two-prong wall
FRONT receptacle is encountered, it must be replaced with a properly grounded
GRILL
three-prong receptacle installed in accordance with the National Elec-
trical Code (NEC) and all applicable local codes and ordinances. This
work must be done only by a qualified electrician, using copper wire only.
WARNING: USE OF A THREE-PRONG TO TWO-PRONG ADAPTER IS
NOT RECOMMENDED. IMPROPER CONNECTION MAY CREATE
THE RISK OF ELECTROCUTION. USE OF SUCH ADAPTERS IS NOT
PERMITTED IN CANADA.
3. Where possible, avoid the use of extension cords. If they must be used,
minimize the risk of overheating by ensuring that they are UL listed and
of the proper gauge and length. Never use a single extension cord to
PLASTIC GRILL
operate more than one fan.
CLIPS
.
4. Do not insert fingers or foreign objects into the fan. Do not block or
a. b. tamper with the fan in any manner while it is in operation. Do not touch
the fan while in operation or just after it has been turned off, as some
parts may be hot enough to cause injury.
5. Unplug power cord before installing or servicing the fan.
WARNING: DO NOT DEPEND UPON THE ON-OFF SWITCH AS THE
SOLE MEANS OF DISCONNECTING POWER WHEN INSTALLING OR
SERVICING THE FAN. ALWAYS UNPLUG THE POWER CORD.
6. This fan is intended for general use ONLY. It must NOT be used in
potentially dangerous locations such as flammable, explosive, chemi-
cal-laden or wet atmospheres.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT USE THIS FAN WITH ANY SOLID STATE SPEED CONTROL
DEVICE.
7. Be sure fan is on a stable surface when operating, to avoid chance of it
overturning.
8. DO NOT use fan in a window. Rain may create an electrical hazard.
9. Completely reassemble fan, according to instructions before reconnect-
ing to power supply.
guard meets OSHA requirements.
MAINTENANCE
WARNING: ALWAYS UNPLUG THE CORD BEFORE SERVICING.
CLEANING: Use a soft cloth and a mild soap solution such as liquid dish
LOW
washing detergent.
906
CAUTION: Do not use gasoline, benzine, thinner, harsh cleaners,
.43 etc. which will damage the fan.
Dry all parts with a soft cloth completely before reconnecting to power
1644
supply.
.32
STORAGE: When not in use, keep unit in a clean dry place.
22
MOTOR IS PERMANENTLY LUBRICATED.
34
1
2084020A