MODELO 4C796E/9146E
OPERACIÓN
1. ÁNGULO VERTICAL: Para ajustar el ángulo vertical, incline la cabeza
del ventilador hacia arriba o hacia abajo según se desee.
2. VELOCIDAD: La velocidad se controla mediante un conjuntor rotatorio
de tres posiciones localizado en la parte trasera del alojamiento del
motor.
3.
CORDÓN DE ALIMENTACIÓN ELÉCTRICA: Enchufe el cordón de
alimentación eléctrica en un receptáculo de pared (120 volts CA, 60
Hz).
MANTENIMIENTO
LISTA DE REPUESTOS
PARTE
NO.
DESCRIPCIÓN
NO.
REF
1
2096065
Rejilla frontal
2
2011754
Paletas
3
2090123
Tuerca hexagonal
4
2011684
Alojamiento del motor y rejilla trasera
5
2011704A
Tornillo de ajuste
6
2091156
Tuerca hexagonal #8-32
7
2011694
Base
8
2010403A
Patas
9
2030078H
Motor
10
2090117
Arandela de bloqueo con dientes ext #8
11
2091119
Tornillo de tierra #6 x 3/8
12
2057062
Interruptor
Rev. C (Color) 2/97
ADVERTENCIA: DESCONECTE SIEMPRE EL CORDÓN ANTES DE
MOVER O DAR SERVICIO AL VENTILADOR.
LIMPIEZA
Utilice un trapo suave, humedecido con una solución de jabón suave. Evite
el uso de gasolina, bencina, diluyentes, solventes clorados, limpiadores
ásperos, etc., ya que causarán daños al ventilador.
LUBRICACIÓN
Los cojinetes de precisión vienen sellados de fábrica de por vida y no
requieren de lubricación adicional.
ALMACENAMIENTO
Cuando no esté en uso, guarde la unidad en un lugar limpio y seco.
ADVERTENCIA: PARA REDUCIR EL RIESGO DE INCENDIOS O
DESCARGAS ELÉCTRICAS, NO USE ESTE VENTILADOR CON
NINGÚN DISPOSITIVO DE CONTROL DE VELOCIDAD DE ESTADO
SÓLIDO.
PARTE
NO.
CANT.
DESCRIPCIÓN
NO.
REF
1
13
2011764
Cubierta trasera del motor
1
15
2091138
Tornillo de la cubierta trasera
2
del motor
1
16
2011724
Interruptor de mando
1
17
2011739
Ornamento
1
18
2050099W
Cordón eléctrico
1
19
2090588
Abrazadera de las paletas
2
1
1
1
1
4
OPERATING INSTRUCTIONS & PARTS MANUAL
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED.
PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH
INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE!
DESCRIPTION
The AirKing 6" (15.2 cm) Air Circulator features whisper quiet
operation, rotary switch control, and adjustable vertical tilt. The
six inch (15.2 cm), 3-paddle fan blade is powered by a perma-
nently pre-lubricated motor.
SPECIFICATIONS
Motor .............................. 120V, 50/60 Hz
Blade diameter ............... 6" ( 15.2 cm)
Cord ............................... 6 ft. (1.8 m), 18/3
Speeds ........................... 2
Control ........................... Rotary Switch
Approvals ....................... UL listed. Close mesh fan guard meets
OSHA requirements.
MODEL
4C796E/9146E
SPEED
HIGH
CFM
566
3
M
/s
.27
RPM
2460
Amps
0.19
Watts
13
dB A
37
GENERAL SAFETY INFORMATION
1. Make certain that the power source conforms to the electrical
requirements of the fan.
2. The power cord is equipped with a three-prong grounded plug
that must be inserted into a matching receptacle. Under no
circumstances must the grounding prong be cut off the plug.
Where a two-prong wall receptacle is encountered, it must be
replaced with a properly grounded three-prong receptacle
CANT.
installed in accordance with the National Electrical Code (NEC)
and all applicable local codes and ordinances. This work must
1
be done only by a qualified electrician, using copper wire only.
WARNING:
USE OF A THREE-PRONG TO TWO-PRONG
2
ADAPTER IS NOT RECOMMENDED. IMPROPER CONNEC-
TION MAY CREATE THE RISK OF ELECTROCUTION. USE OF
1
SUCH ADAPTERS IS NOT PERMITTED IN CANADA.
1
3. Where possible, avoid the use of extension cords. If they must
1
be used, minimize the risk of overheating by ensuring that they
1
are UL listed and of the proper gage and length. Never use a
single extension cord to operate more than one fan.
4. Do not insert fingers or foreign objects into the fan. Do not block
or tamper with the fan in any manner while it is in operation.
5. Unplug power cord before installing or servicing the fan.
WARNING: DO NOT DEPEND UPON THE ON-OFF SWITCH
Rev. C (Color) 2/97
2085300A
R
6" AIR CIRCULATOR
MODEL 4C796E/9146E
READ AND SAVE THESE INSTRUCTIONS
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.
AS THE SOLE MEANS OF DISCONNECTING POWER WHEN
INSTALLING OR SERVICING THE FAN. ALWAYS UNPLUG
THE POWER CORD.
6. This fan is intended for general use ONLY. It must NOT be
used in potentially dangerous locations such as flammable,
explosive, chemical-laden or wet atmospheres. DO NOT use
fan in a window. Rain may create an electrical hazard.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT USE THIS FAN WITH ANY SOLID STATE
SPEED CONTROL DEVICE.
ASSEMBLY
Refer to Figure 1.
1. Remove T-Knob from Fan Head Assembly while being careful
LOW
to retain the Hex Nut on the opposite side.
488
2. Insert the Fan Head Assembly into the Slot on the Stand.
.23
2295
3. Reinstall the T-Knob. Tighten securely.
0.15
11
34
Figure 1
1
2085300A