Specifications - Husky HD219000 Manual De Instrucciones

Operating Instructions
Safety Guidelines
(Continued)
G Always remain in a firmly
balanced position when
using or handling the
nailer.
G Do not modify
or disable the
Work Contact
Element (WCE).
Do not tie or
tape the WCE or
trigger in a
depressed
position. Death
or serious personal injury could
result.
G Do not touch
the trigger
unless driving
nails. Never
attach air line
to nailer or
carry nailer
while touching
the trigger.
The tool could eject a fastener which
will result in death or serious
personal injury.
a potentially hazardous situation
which, if not avoided, COULD result in
death or serious injury.
G Always
disconnect
nailer from air
line before
clearing jams,
adjusting or
servicing the nailer, relocating the
nailer, or when the nailer is not in
use. Always reconnect the air line
BEFORE loading any fasteners. The
Nailer Components And Specifications
• REQUIRES
(SCFM with 16 nails
per minute @ 90 psi)
• AIR INLET 1/4 inch NPT
• NAIL LENGTH
RANGE
• NAIL SHANK 0.113 inch to
RANGE
• MAGAZINE
CAPACITY
• WEIGHT
• LENGTH
• HEIGHT
• MAX PRESSURE
• PRESSURE RANGE
nailer could eject a fastener causing
death or serious personal injury.
G Protect your eyes and
ears. Wear Z87 safety
glasses, with side shields.
Wear hearing protection.
Employers and users are
responsible for ensuring the user or
anyone near the nailer wears this
safety protection. Serious eye
injury or permanent hearing loss
could result.
G Do not use a
check valve or
any other
fitting which
allows air to
remain in the
nailer. Death or
serious personal injury could occur.
G Never place
hands or any
other body
parts in the
nail discharge
area of the
nailer. The
nailer might eject a fastener and
could result in death or serious
personal injury.
G Never carry the
nailer by the air
Warning
hose or pull the
indicates
hose to move
the nailer or a
compressor.
Keep hoses
away from heat,
oil and sharp
edges. Replace any hose that is
damaged, weak or worn. Personal
injury or tool damage could occur.
HD219000 HD289000
4.1 4.1
1/4inch NPT
2 inch 2 inch
1 1
⁄ ⁄
to 3 inch to 3 inch
2 2
0.113 inch to
0.131 inch 0.131 inch
60-75 75-105
8 lbs. 5 oz. 8 lbs. 15 oz.
19.5 inch 21.75 inch
15 inch 15 inch
120 psi 120 psi
70 - 120 psi 70 - 120 psi
G Always assume the nailer contains
G Do not drive a
G Do not operate
G Never leave the nailer unattended or
G Do not drop or throw the tool.
Adjustable Direction
Exhaust Deflector
HD349000
4.1
1/4 inch NPT
2 inch
1
⁄
to 3 inch
2
0.113 inch to
0.131 inch
75-105
8 lbs. 11 oz.
19.75 inch
15 inch
120 psi
70 - 120 psi
2
nails. Never use the nailer as a toy.
Do not engage in horseplay. Always
keep others at a safe distance from
the work area in case of accidental
discharge of nails. Never point the
nailer at anyone. Accidental
triggering of the nailer could result
in death or serious personal injury.
nail on top of
other nails.
The nail could
glance and
cause death or
a serious
puncture wound.
or allow
WARNING
!
anyone else to
operate the
nailer if any
warnings or
warning labels
are not legible. Warnings or warning
labels are located on the nailer
magazine and body.
connected to an air compressor when
not in use. Serious personal injury
can occur if someone picks up and
uses the nailer without knowing the
correct way to operate the nailer.
Dropping or throwing the tool can
result in damage that will make the
tool unusable or unsafe. If the tool
has been dropped or thrown,
examine the tool closely for bent,
cracked or broken parts and air
leaks. STOP and repair before using
or serious injury could occur.
Threaded Hole/Tool
Balancer (M8 x 1.25)
Nail Loading
Area
Single Cycle
Trigger
Magazine
Warning Labels
Nail Discharge Area
Work Contact Element