Loading The Tool; Warranty; Additional Limitations; Unpacking - Husky HDUFL50 Guía De Uso Y Mantenimiento

Safety Information (Continued)

LOADING THE TOOL

1. Do not load the tool with fasteners when any one of the
operating controls is activated.
2.
Never place a hand or any part of body in the fastener
discharge area of the tool.
3. Never point tool at anyone.

Warranty

HUSKY PNEUMATIC NAILER LIMITED TWO-YEAR WARRANTY
This warranty covers defects in workmanship or materials in this HUSKY pneumatic nailer for the two-year period from the date
of purchase. This warranty is specific to this pneumatic nailer. Warranties for other HUSKY products may vary.
This warranty applies only to the original retail purchaser and may not be transferred. This warranty does not cover normal
wear and tear or any malfunction, failure or defect resulting from misuse, abuse, neglect, alteration, modification or repair by
other than a service center authorized to repair HUSKY branded air nailer. Expendable materials, such as O-rings, bumpers,
driver blades, seals, etc. are not covered by this warranty. This warranty does not apply to pneumatic nailer used in industrial
application or for rental purposes. HUSKY makes no warranties, representations or promises as to the quality or performance of
its pneumatic nailer other than those specifically stated in this warranty.

ADDITIONAL LIMITATIONS

To the extent permitted by applicable law, all implied warranties, including warranties of merchantability or fitness for a particular
purpose, are disclaimed. Any implied warranties, including warranties of merchantability or fitness for a particular purpose, that
can not be disclaimed under state law are limited to two years from the date of purchase. HUSKY is not responsible for direct,
indirect, incidental, special or consequential damages. If this pneumatic nailer is used for commercial purposes, the warranty will
apply for ninety (90) days from the date of purchase. Some states do not allow limitations on how long an implied warranty lasts
and/or do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations may not apply to
you. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.
WARNING: The warnings and precautions discussed
above cannot cover all possible conditions and
situations that may occur. It must be understood by
the user that common sense and caution are
factors which cannot be built into this product, but
must be supplied by the user.
6

Unpacking

1. This tool kit has been shipped completely assembled.
2. Carefully remove the tool and any accessories from the
box.
3. Inspect the tool carefully to make sure no breakage or
damage occurred during shipping.
Do not discard the packing material until you have
4.
carefully inspected and satisfactorily operated the tool.
If any parts are damaged or missing, please call
5.
1-888-HD-HUSKY.

Specifications

Air inlet: 1/4 inch NPT
Magazine capacity:
L Cleat &T Cleat: 100 pcs,
Staples: 90 pcs
Weight: 9.96 lbs
Maximum pressure: 115 psi
Pressure range: 70 psi – 115 psi
Pin size range: 1-1/2 inch to 2 inch
T Cleats
7/32"(5.8 mm)
1-1/2" 38 mm
1-3/4" 45 mm
2" 50 mm
(16 Gauge)
Compatible With Generic Brands 1/2 " Crown Staples, T-Cleats, & L-Cleats.
WARNING: If any parts are missing, do not operate the
tool until the missing parts are replaced. Failure to do
so could result in possible serious personal injury.
WARNING: Do not attempt to modify the tool or
create accessories not recommended for use with
the tool. Any such alteration or modification is
misuse and could result in hazardous condition
leading to possible serious personal injury.
L Cleats Staples
9/32"(7.2 mm) 1/2"(12.7mm)
1-1/2" 38 mm 1-1/2" 38 mm
1-3/4" 45 mm 1-3/4" 45 mm
2" 50 mm 2" 50 mm
( 16 Gauge ) (15-1/2 Gauge)
0 075 . " X 0.063"
(1 9 X 1 6 mm)
7
Please contact 1-888-HD-HUSKY for further assistance.
HUSKYTOOLS.COM